Frigidaire FLCE752CAW0 Скачать руководство пользователя

Страница: 50 / 52

PROBLEM

POSSIBLE CAUSES

SOLUTIONS

Water does
not enter
washer or it
enters slowly

• Washer lid is open.

• Water supply is not adequate

in area.

• Water supply faucets are not

completely open.

• Water is being used elsewhere

in the house.

• Water inlet hoses are kinked.

• Close washer lid. The washer will

not operate when the lid is open.

• Check another faucet in the

house. Wait until water supply and
pressure increase.

• Fully open hot and cold faucets.

• Water pressure must be at least 10

psi (69 kPa). Avoid running water
elsewhere while washer is ﬁlling.

• Straighten hoses.

Warm or hot
water is not
hot enough

• Hot water heater is set too

low or is a distance from
washer.

• Hot water is being used

elsewhere in the house.

• Measure hot water temperature at

nearby faucet with candy or meat
thermometer. Water temperature
should be at least 120°F (50°C).
Adjust water heater as necessary.

• Avoid using hot water elsewhere

before or during washer use. There
may not be enough hot water
available for proper cleaning. If
problem persists, your hot water
system may be unable to support
more than 1 use at a time.

Water in
washer does
not drain or
drains slowly

• Drain hose is kinked or

clogged.

• Clean and straighten the drain

hose.

Water leaks

• Loose ﬁll hose connection at

faucet or washer.

• House drain pipes are

clogged.

• Check and tighten hose

connections. Install rubber sealing
washers provided.

• Unclog drain pipes. Contact

plumber if necessary.

Incorrect
wash
and rinse
temperatures

• Hot and cold water hoses are

connected to wrong supply
faucets.

• Connect hot water hose to hot

water faucet and cold water hose
to cold water faucet.

Water is
entering
washer but
tub does not
ﬁll

• Drain hose standpipe is

incorrect height.

• Standpipe must be a minimum

of 33” (84 cm) high to prevent
siphoning. See

Installation section.

Water is
present in
tub after
wash cycle is
complete

• Lid lock malfunction.

• DO NOT bypass lid lock. Call your

authorized service provider.

The drain
and spin
cycles did
not occur

• Lid lock malfunction.

• DO NOT bypass lid lock. Call your

authorized service provider.

Before Calling (continued)

TROUBLESHOOTING

Содержание FLCE752CAW0





















































Результаты поиска

Содержание FLCE752CAW0

Отзывы:

Похожие инструкции для FLCE752CAW0

Бренды по названию

Популярные бренды

Frigidaire FLCE752CAW0, Инструкция по использованию и уходу

Результаты поиска

Содержание FLCE752CAW0

Отзывы:

Похожие инструкции для FLCE752CAW0

Бренды по названию

Популярные бренды