Frigidaire FLCE752CAW0 Скачать руководство пользователя

Страница: 19 / 52

Unpacking instructions

If foam tub block has been removed,
reinsert it now and tape the lid securely.

2. Carefully cut the front and back

corners of the left side of the
remaining cardboard.

3. With help from a second person,

carefully tip the laundry center slightly
to the left as shown in the picture
below. Remove the foam shipping
support from the base of the unit. Save
packaging foam for future use.

4. Carefully lower the laundry center to

an upright position and remove the
tape holding the lid shut. Remove the
foam tub block, all foam inserts, and
other tub contents.

5. From the back of the washer, remove

the wire shipping clips securing the
drain hose.

6. DO NOT remove the PLASTIC CLIPS

which secure the drain hose to the
right side of the washer back sheet.
It helps form a standpipe to prevent
water siphoning.

7. Carefully move the laundry center

to within four (4) feet of the
ﬁnal location for the start of the
installation.

IMPORTANT

To prevent vibration, possible machine
damage and maximize performance,
the following steps must be completed.

NOTE

If the laundry center is to be
transported at a later date, the tub
blocking pad, foam base and tub
support should be retained.

CAUTION

EXCESSIVE WEIGHT HAZARD

To avoid back or other injury, have more
than one person move or lift the appliance.

INSTALLATION

Содержание FLCE752CAW0





















































Результаты поиска

Содержание FLCE752CAW0

Отзывы:

Похожие инструкции для FLCE752CAW0

Бренды по названию

Популярные бренды

Frigidaire FLCE752CAW0, Инструкция по использованию и уходу

Результаты поиска

Содержание FLCE752CAW0

Отзывы:

Похожие инструкции для FLCE752CAW0

Бренды по названию

Популярные бренды