background image

49

TROUBLESHOOTING 

PROBLEM

POSSIBLE CAUSES

SOLUTIONS

Excessive 
wrinkling

• Dryer is overloaded. 

• Items left in dryer too long.
• Insufficient sorting of items.
• Drying temperature too high.

• DO NOT overload. See Operating 

Instructions.

• Remove items as soon as cycle 

ends.

• See Operating Instructions.
• Follow fabric care label instructions.

Scratching 
or chipping 
of the drum 
finish

• Foreign objects such as coins, 

pins, clips or buttons are 
inside the dryer.*

• Permanently attached items 

such as belt buckles, zippers, 
and fasteners may be hitting 
the inside of the drum.*

• Always remove foreign objects from 

pockets before laundering. Remove 
objects from drum and restart dryer. 

• Turn items inside out before drying 

to prevent scratching and damage 
to the dryer.

*Drum damage caused by foreign objects or permanently 
attached items is not covered by the warranty.

WATER

Wash load 
too wet 
after spin

• Washer is overloaded. 

• Load is out of balance.  

• Drain hose is kinked. 

• DO NOT overload washer. See  

Operating Instructions.

• Rearrange load to allow proper  

spinning.

• Straighten drain hose.

Содержание FLCE752CAW0





















































Отзывы: