background image

43

CARE AND CLEANING

RV

ANTIFREEZE

Follow  
Winterizing  
Instructions  
for cold weather  
storage and care.

Winterizing Instructions

1. 

Turn off water supply faucets.

2.  Disconnect hoses from water supply 

and drain water from hoses.

3.  Plug electrical cord into a properly 

grounded electrical outlet.

4.  Add 1 gallon (3.8 L) nontoxic 

recreational vehicle (RV) antifreeze 
to empty wash drum. Close door.

5.  Select the rinse & spin cycle. Start 

the cycle and let the washer drain 
for 1 minute to drain out all the 
water. Not all of the RV antifreeze 
will be expelled.

6.  Stop the cycle, unplug electrical 

power cord, dry off tub interior, and 
close the lid.

7.  Store laundry center in an upright 

position.

8.

To remove antifreeze from washer 
after storage, run empty washer 
through a complete cycle using 
detergent. DO NOT add wash load.

IMPORTANT

Winterize the laundry center if it 
is stored in an area where freezing 
can occur or moved in freezing 
temperatures to prevent damage to the 
washer:

Water inlet hose inspection 

Periodically inspect all water inlet hoses 
for water leaks, wear, cuts, corrosion and 
bulges. Replace all hoses, if any sign of 
the above is visible. All hoses should be 
replaced every 5 years to reduce the risk 
of hose failures. When replacing hoses, 
refer to the Installation sections of this 
Use & Care guide for proper installation 
instructions. DO NOT overtighten or cross 
thread the fittings. DO NOT allow the 
hose to rub against sharp objects. Always 
ensure the hose fitting rubber gasket is 
installed and free from water leaks when 
water pressure is applied. 

Содержание FLCE752CAW0





















































Отзывы: