Frigidaire FLCE752CAW0 Скачать руководство пользователя

Страница: 37 / 52

OPERATING INSTRUCTIONS

Operating the dryer

STEPS

TIPS

IMPORTANT

1. Prepare load

for drying.

• Dry items of similar fabric, weight, and

construction in the same load.

• Separate dark items from light-colored

items. Separate items that shed lint from
those that attract lint.

• Check for stains which may not have been

removed in washing. Repeat stain removal
process and wash again before drying.

• Place delicate or small items in a mesh bag

(not included).

• Be sure buckles, buttons, and trim are

heatproof and won’t damage the drum
ﬁnish. Close zippers, buttons, hooks, and
hook and loop fasteners. Tie strings and
sashes to prevent snagging and tangling.

• Dryer heat may

permanently set
some stains.

2. Check that

the lint ﬁlter
is clean and
in place.

•

• DO NOT operate

dryer without lint
ﬁlter in place.

• DO NOT operate

dryer without
cleaning the ﬁlter
before use.

3. Load the

dryer and
close the
door.

• Load items loosely. The average wet load

will ﬁll the drum 1/3 to 1/2 full. Items need
room to tumble freely for even drying and
less wrinkling.

• If desired, place a dryer fabric softener

sheet on top of the load at the beginning
of the cycle.

• When drying large items, dry only two or

three items at a time. Fill out the load with
smaller items.

• For delicate or very small loads, add two or

three similar items to improve tumbling action.

• DO NOT overload

the dryer.

WARNING

To reduce the risk of ﬁre, electric shock
or injury to persons, read the Important
Safety Information in this

Use & Care

Guide before operating your dryer.

CAUTION

• DO NOT operate dryer without lint

ﬁlter in place.

• ALWAYS clean ﬁlter after each load.

Содержание FLCE752CAW0





















































Результаты поиска

Содержание FLCE752CAW0

Отзывы:

Похожие инструкции для FLCE752CAW0

Бренды по названию

Популярные бренды

Frigidaire FLCE752CAW0, Инструкция по использованию и уходу

Результаты поиска

Содержание FLCE752CAW0

Отзывы:

Похожие инструкции для FLCE752CAW0

Бренды по названию

Популярные бренды