Frigidaire FLCE752CAW0 Скачать руководство пользователя

Страница: 9 / 52

PRE-INSTALLATION REQUIREMENTS

Shipping hardware

Foam shipping restraint (inside
wash tub) removed and stored

Foam shipping support (underneath
appliance) removed and stored

Leveling

Laundry center is level, side-to-side
and front-to-back

Cabinet is sitting solid on all corners

Water supply

Use only new hoses and verify
rubber sealing washers are installed

HOT supply is connected to HOT
inlet and COLD supply is connected
to COLD inlet

HOT and COLD water supply turned on

No leaks present at water supply
connections or appliance inlet
connections-recheck after 24 hours

Drain

Stand pipe or wall drain height min. 33”

Drain hose secured in place with
cable tie (shipped in drum)

Exhaust venting

Free-ﬂowing, clear of lint buildup

4 inch (102 mm) rigid or semi-rigid
ducting of minimal length and turns

NO foil or plastic venting material

Approved vent hood exhausted to

Installation Checklist

outdoors

Gas supply (Gas Dryer)

Manual shutoff valve present in supply

All connections sealed with
approved sealer and wrench tight

Conversion kit for LP system

Gas supply turned on

No leaks present at all connections -
check with soapy water, NEVER
check with ﬂame

208v/240V electric supply
(electric dryer)

Approved NEMA 10-30 or 14-30
service cord with all screws tight on
terminal block

Approved strain relief installed

Terminal access cover installed
before initial operation

Electrical power

House power turned on

Laundry Center plugged in

Final checks

Installation Instructions and Use &
Care Guide read thoroughly

Water enters drum when cycle
starts with lid lowered

Dryer door latches and drum
tumbles when cycle starts

Registration card sent in

Tool requirements

Tools and materials needed for installation:

• Adjustable

pliers

•

Phillips, straight, & square bit
screwdrivers

• Adjustable

wrench

•

Pipe wrench for gas supply (gas dryer)

•

LP-resistant thread tape (for natural
gas or LP supply, gas dryer)

• Carpenter’s

level

•

External vent hood

•

4-inch (102 mm), rigid metal or semi-
rigid metal exhaust duct work

•

3-wire or 4-wire 240 volt cord kit
(electric dryer)

•

4 in. (102 mm) clamp

•

Gas line shutoff valve (gas dryer)

•

1/2 NPT union ﬂare adapters (x2) and
ﬂexible gas supply line (gas dryer)

•

Metal foil tape (not duct tape)

•

Inlet hoses (x2)

NOTE

Hoses are not included with washer
purchase.

Содержание FLCE752CAW0





















































Результаты поиска

Содержание FLCE752CAW0

Отзывы:

Похожие инструкции для FLCE752CAW0

Бренды по названию

Популярные бренды

Frigidaire FLCE752CAW0, Инструкция по использованию и уходу

Результаты поиска

Содержание FLCE752CAW0

Отзывы:

Похожие инструкции для FLCE752CAW0

Бренды по названию

Популярные бренды