Freestyle FS-120 LP, Инструкция по эксплуатации

Страница: 70 / 120

&IGURE /FFSET
a
DJUSTMENTSCREW
nn
/.,9FORUSEBYAQUALIlEDTECHNICIANUSING
CALIBRATEDCOMBUSTIONTESTINSTRUMENTS
Part number 550-142-850/0115
70
FreeStyle
™
W
ALL
M
OUNT GAS
-
FIRED WATER BOILER
—
Boiler Manual
.ATURAL'AS!CCEPTABLE #OMBUSTION2ANGE
-INIMUM2ATEAFTERMINUTESFROMCOLD
Boiler Model CO/(PPM) CO
2
NG % CO
2
LP %
&3
20
n n
&3
20
n n
At Minimum Rate:
1. Adjust the boiler to minimum output and allow the boiler
to stabilize.
2.
.OWADJUSTTHEOFFSETPRESSURESETTING
Figure 97 - cup B) Torx
(T-40 male driver) until the CO
2
ISATTHECORRECT3%44).'
LEVEL (see Figure 98), confirm that the CO/CO
2
ratio is
within limits (clockwise to increase gas).
28
6WDUWXS²¿QDOFKHFNV
(continued)
Re-check the Minimum Rate
3.
4URNOFFTHEBOILERANDTHENTURNITBACKONANDPUTIN4EST
-ODEATMAXIMUMFORMINUTETHENREDUCElRINGRATE
HIGHlREFORMINUTES2EDUCETOMINIMUMANDRECHECK
the minimum rate output ensuring the CO
2
setting level has
remained unchanged and confirm that the CO/CO
2
ratio
is within limits.
4. In the event that the CO
2
setting level with an acceptable
CO/CO
2
ratio cannot be obtained please contact your
Williamson-Thermoflo representative.
5. Should you require any assistance during the set up pro-
cedure contact your Williamson-Thermoflo representative
IFTHEPROBLEMCANNOTBEADDRESSEDWITHTHEINFORMATION
provided in this manual.
❏
#HECK(EATEXCHANGERANDVENTSEALS
1.
/PERATETHEBOILERON()'(lRE
2.
!LEAKWOULDAPPEARASVAPORONTHESURFACEOFTHEMIRROR
3.
)FTHEREISANYINDICATIONOFALEAKATANYJOINTIMMEDIATELY
shut down the boiler.
a.
)FPOSSIBLETIGHTENTHERETAININGSCREWSORNUTSWITHOUT
over-tightening).
b. )F THIS DOES NOT CORRECT THE PROBLEM DISASSEMBLE THE
components where the leak appeared. Use the proce-
DURESGIVENINTHE-AINTENANCESECTIONOFTHISMANUAL
c. When disassembling components, inspect gaskets to see
IFTHEREISDAMAGE2EPLACEANYDAMAGEDGASKET
d. #ONTACTYOUR7ILLIAMSON4HERMOmOREPRESENTATIVEIF
THEPROBLEMCANNOTBEADDRESSEDWITHTHEINFORMATION
provided in this manual.
❏
#HECKIGNITIONSYSTEMSAFETYSHUTOFFDEVICE
1. !FTERTHEBOILERHASBEENINSTALLEDTURNOFFTHEBOILER
2. 3HUTOFFTHEMANUALGASVALVELOCATEDONTHEGASLINETOCUT
mOWOFFUELTOTHEBOILER
3. Turn on the boiler. It will start to ignite and a “ d3” code will
mASH!FTERTHEh d3” CODEmASHFORSOMETIMETHEBOILERWILL
go into a Lockout condition and a “
!
” code will show in
the display. It means that the boiler tried to ignite without
success (code “
d3”
FOR THREE TIMES AND WHEN INTO
Lockout mode(code “ ! ”). This means that the ignition
SYSTEMSAFETYDEVICEWORKEDPROPERLY
4. Open the manual gas valve located on the gas line to resume
FUELSUPPLYTOTHEBOILER
5. Hit the “ Reset ” button once to Clear the Lockout code “
!
”.
&IGURE Minimum rate combustion values –
measured values must be within the ranges
given below
!DJUSTINSTEPSOFNOMORETHANOFATURNAND
WAITMINUTEAFTEREACHADJUSTMENTTOALLOWTHE
SETTINGTOSTABILISE4URNINGTHESCREWTOOFARWILL
cause the adjustment to reverse behavior.
/FFSETADJUSTMENT
B
Offset Regulating screw
Test at MIN. Power 00%
Turn clockwise (open gas)
IRU³0$;JDVÀRZ´
Turn counter-clockwise
(close gas)
IRU³0,1JDVÀRZ´