Freescale Semiconductor MK22FN256VDC12 Скачать руководство пользователя страница 703 | Manualshive

Страница: 703 / 1313

background image

ADCx_CFG2 field descriptions (continued)

Field

Description

0

Normal conversion sequence selected.

1

High-speed conversion sequence selected with 2 additional ADCK cycles to total conversion time.

1–0

ADLSTS

Long Sample Time Select

Selects between the extended sample times when long sample time is selected, that is, when
CFG1[ADLSMP]=1. This allows higher impedance inputs to be accurately sampled or to maximize
conversion speed for lower impedance inputs. Longer sample times can also be used to lower overall
power consumption when continuous conversions are enabled if high conversion rates are not required.

00

Default longest sample time; 20 extra ADCK cycles; 24 ADCK cycles total.

01

12 extra ADCK cycles; 16 ADCK cycles total sample time.

10

6 extra ADCK cycles; 10 ADCK cycles total sample time.

11

2 extra ADCK cycles; 6 ADCK cycles total sample time.

33.3.4 ADC Data Result Register (ADCx_Rn)

The data result registers (Rn) contain the result of an ADC conversion of the channel
selected by the corresponding status and channel control register (SC1A:SC1n). For
every status and channel control register, there is a corresponding data result register.

Unused bits in R n are cleared in unsigned right-aligned modes and carry the sign bit
(MSB) in sign-extended 2's complement modes. For example, when configured for 10-bit
single-ended mode, D[15:10] are cleared. When configured for 11-bit differential mode,
D[15:10] carry the sign bit, that is, bit 10 extended through bit 15.

The following table describes the behavior of the data result registers in the different
modes of operation.

Table 33-43. Data result register description

Conversion

mode

D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0

Format

16-bit differential S

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

Signed 2's
complement

16-bit single-
ended

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

Unsigned right
justified

13-bit differential S

S

S

S

D

D

D

D

D

D

D

D

D

D

D

D

Sign-extended
2's complement

12-bit single-
ended

0

0

0

0

D

D

D

D

D

D

D

D

D

D

D

D

Unsigned right-
justified

11-bit differential S

S

S

S

S

S

D

D

D

D

D

D

D

D

D

D

Sign-extended
2's complement

10-bit single-
ended

0

0

0

0

0

0

D

D

D

D

D

D

D

D

D

D

Unsigned right-
justified

Table continues on the next page...

Chapter 33 Analog-to-Digital Converter (ADC)

K22F Sub-Family Reference Manual , Rev. 3, 7/2014

Freescale Semiconductor, Inc.

703

«
...
701
702
703
704
705
...
»

Содержание MK22FN256VDC12


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MK22FN256VDC12

Бренд: Barco Страницы: 6

Бренд: Taie Страницы: 28

Бренд: IBM Страницы: 276

Бренд: IBM Страницы: 157

Бренд: ICP DAS USA Страницы: 166

Бренд: ICP DAS USA Страницы: 64

Tunnel Master Jr

Бренд: ICS Страницы: 83

Бренд: ZKTeco Страницы: 14

Бренд: Unico Страницы: 164

Бренд: Full Gauge Controls Страницы: 3

Бренд: Linear Technology Страницы: 7

J1000 CIMR-JC series

Бренд: YASKAWA Страницы: 25

Бренд: EpiSensor Страницы: 37

Бренд: ICP DAS USA Страницы: 26

Бренд: National Instruments Страницы: 22

Бренд: PI Страницы: 111

Бренд: Melexis Страницы: 13

Бренд: Zennio Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды