Freefly Alta 8 Pro Скачать руководство пользователя страница 97 | Manualshive

Страница: 97 / 128

Freefly Alta 8 Pro Скачать руководство пользователя страница 97

ALTA Pro will notify the pilot of critical alarms through QGroundControl. These alarms
indicate a serious issue has been observed in the behavior of the ALTA Pro that, if not acted
upon immediately, can cause loss of control. Never continue a flight when ALTA Pro indicates
an alarm!

Aircraft Monitor

ALTA Pro QGroundControl includes a flight status monitor that displays information about
the health of the ALTA Pro and the various controls that can be selected.

Icon

Name

Description

Boot

Indicates if the PX4 has completed its booting process and
whether it was successful. Any issues that prevented a normal
boot are indicated here.

Battery

Displays the voltage of the battery packs.

Status

Displays the state of the PX4 flight controller.

Radio

Displays if the PX4 detects a radio controller signal. A LOS
warning is displayed if no signal is present.

GPS

Displays if PX4 has resolved a GPS fix or not.

Sats

Displays the number of GPS satellites in view and being received.
A minimum of 6 satellites are required in order to enter Position
Mode.

Lock

Clicking on this icon displays whether a position lock is ready,
indicating a valid GPS fix and good heading. This is required
before the Autopilot will allow switching into Position Mode.

Altitude

Displays the current height control mode: Manual, Vario if in
Height or Position mode and climbing or descending, and Hold.

«
...
95
96
97
98
99
...
»

Содержание Alta 8 Pro

































































































































Отзывы:

Нет отзывов