Freefly Alta 8 Pro Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 128

Freefly Alta 8 Pro Скачать руководство пользователя страница 85

Selecting the ‘Reset all to defaults’ option in the Tools menu will reset all
parameters to the QGroundControl defaults. These are not the same as the
ALTA Pro default parameters. To reset to ALTA Pro defaults load the ALTA
PRO Default Parameters to the aircraft.

Updating your Wifi Password and SSID

Enabling and Updating Your Wifi Password and SSID

1. Connect to ALTA Pro using the Radio Modem or USB

2. Go to the System Parameters under the Parameter tab in the Vehicle Setup menu and

find the SYS_COMPANION parameter.

3. Change the SYS_COMPANION parameter to ‘ESP8266 (921600 baud, 8N1)’ and restart

ALTA Pro to enable the WiFi connection.

To enable WiFi connectivity follow the steps below!

Please read this entire section if you intend to use the WiFi feature of ALTA
Pro.

When flying multiple aircraft with WiFi enabled, take extreme caution to
ensure that the aircraft connected to the laptop/mobile device is the desired
craft. Failing to connect to the correct device may result in an inadvertently
arming a aircraft or disarming one that is inflight.

ALTA Pro allows users to update the system’s WiFi password and SSID. All ALTA Pro’s
initially come with WiFi disabled for safety reasons.

«
...
83
84
85
86
87
...
»

Содержание Alta 8 Pro

































































































































Отзывы:

Нет отзывов