Freefly Alta 8 Pro Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 128

Freefly Alta 8 Pro Скачать руководство пользователя страница 83

This parameter determines the flight mode ALTA Pro will enter if it detects a Loss-of-Signal
(LOS). Selecting ‘Land at Current Position’ will cause ALTA Pro to Autoland in place when
the LOS is detected. Selecting ‘Return to Land’ will cause ALTA Pro to Return-to-Land and
then Autoland when the LOS is detected.

Return Home Settings

Used to set the RTL altitude, loiter time, and RTL behavior.

Land Mode Settings

This adjusts the descent rate of the ALTA Pro during Autoland in meters per second. This
value is applied to the Autoland descent profile for the final 15 meters above the ground until
landing. This option also provides the option to automatically disarm ALTA Pro after landing.

Saving, Loading, and Resetting Parameters

Saving, Loading, and Resetting Parameters

ALTA Pro QGroundControl allows users to save, load, and reset all of ALTA Pro’s
parameters. This is useful when trying to save certain parameters that will need to used
again in the future or when troubleshooting and needing to get back to a known good state.

«
...
81
82
83
84
85
...
»

Содержание Alta 8 Pro

































































































































Отзывы:

Нет отзывов