Freefly Alta 8 Pro Скачать руководство пользователя страница 48

Страница: 48 / 128

Name

Options

Description

OSD_ENABLE

Enabled/Disabled

Turns OSD on or off

OSD_PAL_NTSC

PAL / NTSC

Indicates the FPV video camera
format to PX4

OSD_UNITS

Metric / Imperial

Changes the displayed units

OSD_HOR_OS

Min: 1

Centers the OSD components
horizontally

OSD_VER_OS

Min: 1

Centers the OSD components
vertically

OSD_LEFT_OS

Min: 1

Controls the margin to the left of the
OSD

OSD_LOWER_OS

Min: 1

Controls the margin underneath the
OSD

OSD_RIGHT_OS

Min: 1

Controls the margin to the right of the
OSD

OSD_UPPER_OS

Min: 1

Controls the margin above the OSD

OSD_BAT_ALARM

3.000 - 4.200

Sets battery cell levels that trigger an
on screen warning

OSD_MAX_ALTITUDE

Min: 1.000

Default: 121.900

Creates an on screen warning when
exceeding the set max altitude
(meters)

OSD_MAX_CLIMB

Min: 0.000

Default: 3.500

Creates an on screen warning when
exceeding the set max climbing rate
(meters per second)

OSD_MAX_RANGE

Min: 1.000

Default: 1000.000

Creates an on screen warning when
exceeding the set max range (meters)

Содержание Alta 8 Pro

































































































































Результаты поиска

Содержание Alta 8 Pro

Отзывы:

Freefly Alta 8 Pro, Руководство пользователя, Страница: 48 / 128

Результаты поиска

Содержание Alta 8 Pro

Отзывы: