manualshive.com logo in svg

Fractal Audio axe-fx ultra, Руководство пользователя

Поделиться
Скачать
Fractal Audio axe-fx ultra Скачать руководство пользователя страница 84

The Effects

81

The controls are linear (as opposed to logarithmic like most other gain controls). This makes setting 
up cross-fades much easier.

Volume / Pan

The Volume / Pan block is a simple level and pan control block. It allows you to insert level and 
pan controls at any point in the routing matrix. It is a great way to control the level into or out of 
effects using an expression pedal.

VOLUME - 

Sets the volume level out of the block.

BALANCE - 

Sets the balance (L/R) out of the block.

VOLUME TAPER - 

Sets the “taper” of the volume control. Linear selects a linear taper. 

LOG A

 

selects a logarithmic taper where the attenuation is 10 dB when the volume control is at 5.00. 

LOG 

B

 selects a log taper where the attenuation is 20 dB at midscale.

Feedback Send / Return

The Feedback Send and Return blocks allow you to feedback sound from one point in the routing 
to any other point.

The Send block has no parameters, while the Return block has a basic mixer. Adjust the 

MIX

 control 

to set the ratio of direct and feedback signals.

Best results are achieved when feeding back a pure delayed signal. If any direct signal is fed back 
the resulting loop will usually be unstable and/or sound strange due to phase cancellation.

Warning: Use caution with the Feedback blocks as you can easily program an unstable loop and cause 
internal clipping of the signal and/or very high sound levels which can damage your hearing. Always 
start with the 

MIX

 control on zero and slowly bring it up. If you start to hear squealing or other signs of 

instability return the 

MIX

 control to zero and analyze your routing for possible causes of instability.

Содержание axe-fx ultra






































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды