manualshive.com logo in svg

Fractal Audio axe-fx ultra, Руководство пользователя

Поделиться
Скачать
Fractal Audio axe-fx ultra Скачать руководство пользователя страница 79

The Effects

76

VOICE1,2 SHIFT - 

Sets the shift amount of the voice in half-steps. The range of shift is +/- 12 half-

steps.

VOICE1,2 LEVEL - 

Sets the volume level of the voice.

VOICE1,2 PAN - 

Sets the panning of the voice.

VOICE1,2 DELAY - 

Sets the delay time of the voice in milliseconds.

VOICE1,2 DLYTEMPO - 

Locks the delay time to the global tempo. For example, if the global tempo 

is 120 bpm and the tempo is set to a quarter note (1/4) then the delay time will be 500 ms. To ignore 
the global tempo set the tempo control to 

NONE

.

VOICE1,2 SPLICE - 

Sets the splice time of the voice in milliseconds.

VOICE1,2 SPLTEMPO - 

Locks the splice time to the global tempo. For example, if the global 

tempo is 120 bpm and the tempo is set to a quarter note (1/4) then the time will be 500 ms (one echo 
per beat). To ignore the global tempo set the tempo control to 

NONE

.

VOICE1,2 FEEDBACK - 

Sets the feedback of the voice to the input. By delaying and feeding a 

voice back strange pitch effects can be created as the note is translated pitch again and again.

DIRECTION - 

Sets the “direction” of the splice playback. Try setting to 

REVERSE

 for spacey 

effects.

FEEDBACK TYPE - 

Selects the type of feedback. DUAL sends the individual voices back to their 

respective delay lines. 

BOTH

 mixes the voices and sends them back to both delay lines. 

PING-

PONG

 sends each voice to the opposite delay line.

HICUT FREQ - 

Sets the high-frequency rolloff of the pitched signal using a 12 dB / octave filter. 

This can be used to adjust the timbre of the voices.

CROSSFADE - 

Sets the amount of overlap in the audio snippets. A low setting will make the echoes 

more discrete whereas a high setting will tend to smear the echoes.

Advanced Whammy

The Advanced Whammy mode is identical to the Classic Whammy mode except that the start and 
stop shift amounts are controllable in semitone increments. This allows you to set the heel down to 
any amount of shift and the toe down to any amount of shift rather than being constrained to pre-
programmed intervals.

Parameters

The parameters for the Advanced Whammy are the same as the Classic with the following 
differences:

START - 

Sets the start pitch shift amount in semitones. This is the amount of pitch shift when the 

CTRL knob is in the minimum position.

Содержание axe-fx ultra






































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды