Fractal Audio axe-fx ultra Скачать руководство пользователя страница 81

Страница: 81 / 101

The Effects

Parameters

All parameters are the same as the Intelligent Harmony mode with the following exceptions:

VOICE n SCALE -

Selects the custom Global Scale to use. See the Global section for more details

on Global Scales.

Auto Pitch

The Auto Pitch mode corrects the pitch of the input. This can be used to correct vocal performances
or as a special effect.

All parameters for the Auto Pitch mode are described under the Intelligent Harmony mode.

Synth

The Axe-Fx Ultra

contains two dual-voice monophonic synthesizers. These are classic oscillator-

based synthesizers and can be used to do synth leads with your guitar or other instrument input.
Alternatively the can be controlled manually.

Parameters

Each synth has two voices with the following parameters:

TYPE -

Selects the type of waveform. Sine and triangle are the smoothest while the square and ramp

types are more “buzzy”.

TRACK -

Selects the type of input tracking.

OFF

allows the frequency and level to be set manually

via the

FREQ

and

LEVEL

controls.

ENV ONLY

selects the level to be controlled by the envelope of the

input with the frequency set manually.

PITCH+ENV

selects the frequency and level to be controlled

by the pitch and envelope of the input.

FREQ -

If input tracking is set to

OFF

ENV ONLY

this parameter sets the oscillator frequency.

SHIFT -

Shifts the frequency of the oscillator up or down in semitone steps.

TUNE -

Detunes the oscillator slightly. The oscillator can be d/- 50 cents.

DUTY -

When using the

TRIANGLE

SQUARE

waveforms this parameter controls the duty cycle of

the waveform.

LEVEL -

Controls the output level of the oscillator.

PAN -

Controls the panning of the oscillator.

FILTER -

Sets the cutoff frequency of a low-pass filter after the oscillator.

Q -

Sets the Q of the post-oscillator filter.

ATTACK -

Sets the attack time of the envelope follower on the input.

Содержание axe-fx ultra






































































































Результаты поиска

Содержание axe-fx ultra

Отзывы:

Бренды по названию

Популярные бренды

Fractal Audio axe-fx ultra, Руководство пользователя

Результаты поиска

Содержание axe-fx ultra

Отзывы:

Бренды по названию

Популярные бренды