Forum SSW 40 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 88

Forum SSW 40 Скачать руководство пользователя страница 50

5

Service

INFO

Operational safety and readiness of the SSW-40
do not only depend on your skill, but also on
maintenance and servicing the SSW-40. Insist
on using original spare parts when carrying
out maintenance and repair work. This ensures
operational safety and readiness of your SSW-40,
and maintains its value.

5.1

Malfunction

If a malfunction occurs or the SSW-40 does not operate as
expected, troubleshoot as follows:
If the cause of the malfunction cannot be determined
and remedied, contact FORUM Handling Tools Technical
Support.
1.  Check pneumatic connections and pneumatic lines.
2.  Check the present necessary pneumatic pressure.
3.  Check that the required components correspond to

the used pipe size.

4. Check for proper lubrication of the SSW-40.
5. Collect all information on the malfunction and define

the problem.

6.  Attempt to find a quick solution to the problem.
7.  Check the last changes/modifications.
8.  Isolate the problem.
9.  Replace any defective components.

INFO

In the event of problems, which cannot be
remedied with the aid of this OMM, please
contact the FORUM Handling Tools Technical
Support or one of the authorized service
companies
(„Contact Worldwide", on page 10).

5.2

Repair

5.2.1

Repair by Customer

It is only permissible for the customer/company operating
the SSW-40 to replace defective parts with OEM
(Original Equipment Manufacturer) parts approved by
FORUM Handling Tools in conformance with the present
operating instructions. Use of parts not approved by
FORUM Handling Tools voids the warranty.

5.2.2

Repair by Manufacturer

Ensure that only FORUM Handling Tools or an authorized
service company performs any repair work required on the
SSW-40.

INFO

Please contact the FORUM Handling Tools
Technical Support or one of the authorized
service companies („Contact Worldwide", on
page 10) to perform repair or maintenance
work.

5.2.3

Securing Screws with Wedge-
Locking washers

Wedge-Lock style bolt securing systems use geometry to
safely lock bolted joints in the most critical applications.
The key is the difference in angles. Since the cam angle
„∂“ is larger than the thread pitch „ß“, the pair of washers
expands more than the corresponding pitch of the thread.
Any attempt from the bolt/nut to rotate loose is blocked
by the wedge effect of the cams. When the pushed
movements of the equipment will get in contact with the
under surface of the securing plate, this surface contact
will secure the plate and prevents any motion in the axial
direction.

Fig. 34: Wedge-Locking Washer principle illustration

Operation Maintenance Manual

Safety Spinning Wrench

PN 9GV73109 - Revision: 02 2018-05

50

SE

RV

ICE

«
...
48
49
50
51
52
...
»

Содержание SSW 40

























































































Отзывы:

Нет отзывов