manualshive.com logo in svg

Forum SSW 40, Руководство по эксплуатации, Страница: 34 / 88

Поделиться
Скачать
Forum SSW 40 Скачать руководство пользователя страница 34

Operation Maintenance Manual

 

Safety Spinning Wrench  

 PN 9GV73109 - Revision: 02 2018-05

34

TR

A

N

SP

O

RT/

 

IN

STA

LL

AT

IO

N

3 

Transport and Setup

Ensure that only sufficiently qualified 
and trained personnel accomplish 
transport and setup work.

Read these instructions carefully before 
setting up the Equipment and putting 
it into service.

3.1 

Delivery

The SSW-40 and all accessory parts are shipped on 
transport pallets or crates. All items on the pallets are 
secured against tipping and slipping with transport straps.

 

» Instructions for safe transport are attached to the 

transport crate.

 

» Transport the packed equipment as specified in these 

instructions.

Scope of Delivery

INFO

The contract documents and shipment papers 
specify the precise scope of delivery. Check 
these documents carefully on delivery. In the 
event of any discrepancies please contact 
the FORUM Handling Tools representative 
immediately  
(„XI Contact  Worldwide“, on page 10).

The scope of supply includes all components required for 
the intended operation of the SSW-40:

 

- Safety Spinning Wrench as described  

in Chapter „1 DESCRIPTION“, on page 16. 
For detailed scope, refer to purchase order.

3.1.1 

Unpacking and Disposal 
of Packing Material

Remove the transport packaging and transport aids before 
hoisting the SSW-40.

 

NOTE

 Do not remove transport retainers! Remove 

transport retainers only at the installation site just before 
startup.

Check scope of delivery

1.  Is any transport damage visible?
2.  Is the shipment complete? Compare the scope 

of delivery with the specifications in the shipping 
documents.

If the SSW-40 has been damaged during transport or the 
shipment is incomplete, please notify the manufacturer 
immediately („XI Contact  Worldwide“, on page 10).
Dispose of the packaging material ecologically in 
compliance with all applicable regulations.

3.1.2 

Intermediate Storage

If intermediate storage of the Equipment is necessary, 
observe the following:
•  Leave the SSW-40 it its transport packaging. This 

provides sufficient protection against external 
influences.

•  Secure the SSW-40 to prevent it from slipping or falling 

due to motion.

Fig. 22:  Typical transport and conservation packing for a SSW-40

Содержание SSW 40

























































































Отзывы:

Нет отзывов