manualshive.com logo in svg

Formulatrix NT8, Руководство пользователя

Поделиться
Скачать
Formulatrix NT8 Скачать руководство пользователя страница 72

68

NT8 User's Guide | Chapter 15: System Maintenance

What You Will Need:

●

A small paint brush (shipped in your accessory kit).

●

Grease (shipped in your accessory kit).

●

A deep well block filled about half way with water colored with food dye.

●

A daughter plate.

●

A High Volume tip caddy with 8 HV tips.

Lubricating the O-rings

1.

Open the hood to expose the NT8’s head and deck.

2.

Using the paintbrush, lightly but evenly apply grease to the front and back of each of
the eight O-rings on the NT8’s plate copy head.

3.

When you are finished, power-on the NT8 and continue with “Running a Plate Copy
Test".

If you are attempting to lubricate the plate copy plungers, you will first need to edit the user
interface configuration file in order to display the programmatic tab.

To enable the programmatic tab:

1.

If you are running the NT8 software, exit the software.

2.

Go to

C:\ProgramData\Formulatrix\NT8\1\Data\Device\Configs

.

3.

Find

UserInterface.config

 and open the file.

Enabling the Programmatic Tab

Содержание NT8
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды