manualshive.com logo in svg

Formulatrix NT8, Руководство пользователя

Поделиться
Скачать
Formulatrix NT8 Скачать руководство пользователя страница 28

24

The NT8 has humidifiers that actively maintain moisture levels up to 90% to prevent drop
evaporation. Please ensure that the NT8 chambers have enough water for proper function.

To configure your humidifiers:

1.

Click the

Options

 button        and go to the

Advanced Options

 tab.

2.

Configure the

Humidifier Control

 settings.

●

Enabled

: If set to

True

, enables the NT8 to monitor and control the humidifiers

as necessary.

●

Humidity Level (%)

: Set the humidity level to turn off the humidifier. When the

humidity level reaches the limit, the system automatically turns off the humidifier.

3.

Click

Save

.

Occasionally you might want to empty and clean the system liquid and humidifier chamber
that serve your NT8. To do so, you'll need to turn the pump control settings off while you're
cleaning the chambers and then turn them back on.

Prerequisites

●

Humidifier is on manual mode (click

on the toolbar to switch to manual mode).

Emptying and Filling System Liquid and Humidifier Chambers

Important

: The following tutorial is for advanced users and administrators only.

Important

: The following tutorial is for advanced users and administrators only.

M

Содержание NT8
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды