Ford 2010 Milan Hybrid страница 63 Скачать руководство пользователя

Страница: 63 / 326

2. At the wheel well, remove the
press pins from the splash shield.

3. Reaching through the wheel well,
remove the rubber bulb access
cover from the housing.

4. Remove the bulb socket by rotating it counterclockwise, then pull it
straight out of the lamp assembly.

5. Disconnect the electrical
connector from the bulb socket and
discard the old bulb socket.

WARNING:

Handle a halogen headlamp bulb carefully and keep

out of children’s reach. Grasp the bulb only by its plastic base

and do not touch the glass. The oil from your hand could cause the
bulb to break the next time the headlamps are operated.

6. Connect the new bulb socket to the electrical connector.

2010 Milan

(mln)

Owners Guide, 1st Printing
USA

(fus)

Lights

Содержание 2010 Milan Hybrid







































































































































































































































































































































Результаты поиска

Содержание 2010 Milan Hybrid

Отзывы:

Похожие инструкции для 2010 Milan Hybrid

Бренды по названию

Популярные бренды

Ford 2010 Milan Hybrid, Руководство пользователя

Результаты поиска

Содержание 2010 Milan Hybrid

Отзывы:

Похожие инструкции для 2010 Milan Hybrid

Бренды по названию

Популярные бренды