manualshive.com logo in svg

Ford 2010 Milan Hybrid, Руководство пользователя

Владельцы Ford 2010 Milan Hybrid могут бесплатно загрузить руководство по эксплуатации на нашем сайте. Узнайте все о своем автомобиле, используя наше руководство. Просто скачайте его с manualshive.com и получите все необходимые сведения для правильного использования и обслуживания вашего автомобиля.

Поделиться
Скачать
background image

All components of the AWD system are sealed for life and require no
maintenance.

Note:

When an AWD system fault is present, the warning CHECK AWD

will display in the message center. The AWD system is not functioning
correctly and defaulted to front wheel drive. When this warning is
displayed, have your vehicle serviced at an authorized dealer.

If your vehicle is equipped with AWD, a spare tire of a different size
other than the tire provided should never be used. A dissimilar spare tire
size (other than the spare tire provided) or major dissimilar tire sizes
between the front and rear axles could cause the AWD system to stop
functioning and default to front wheel drive.

Note:

Your AWD vehicle is not intended for off-road use. The AWD

feature gives your vehicle some limited off-road capabilities in which
driving surfaces are relatively level, obstruction-free and otherwise
similar to normal on-road driving conditions. Operating your vehicle
under other than those conditions could subject the vehicle to excessive
stress which might result in damage which is not covered under your
warranty.

Driving on slippery surfaces with AWD vehicles

AWD vehicles are specially equipped for driving on sand, snow, mud and
rough roads and have operating characteristics that are somewhat
different from conventional vehicles, both on and off the highway.

When driving at slow speeds off-highway under high outside
temperatures, use a low gear or (L) when possible. L (Low) gear
operation will maximize the engine and transmission cooling capability.

Under severe operating conditions, the A/C may cycle on and off to
protect overheating of the engine.

Basic operating principles

•

Drive slower in strong crosswinds which can affect the normal steering
characteristics of your vehicle.

•

Be extremely careful when driving on pavement made slippery by
loose sand, water, gravel, snow or ice.

If your vehicle goes off the edge of the pavement

•

If your vehicle goes off the edge of the pavement, slow down, but
avoid severe brake application, ease the vehicle back onto the
pavement only after reducing your speed. Do not turn the steering
wheel too sharply while returning to the road surface.

2010 Milan

(mln)

Owners Guide, 1st Printing
USA

(fus)

Driving

226

Содержание 2010 Milan Hybrid







































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2010 Milan Hybrid

Daihatsu F300 Service Manual preview
F300
Бренд: Daihatsu Страницы: 1718
RaceChip Pro 2 Installation Manual preview
Pro 2
Бренд: RaceChip Страницы: 12
Vauxhall Ampera Owner'S Manual preview
Ampera
Бренд: Vauxhall Страницы: 199
HUSKY LINERS X-ACT CONTOUR 53491 Care And Use Instructions preview
X-ACT CONTOUR 53491
Бренд: HUSKY LINERS Страницы: 2
Volvo 30728293 Installation Instructions Manual preview
30728293
Бренд: Volvo Страницы: 19
Club Car Gasoline/Electric DS Golf Car 1996 Owner'S Manual preview
Gasoline/Electric DS Golf Car 1996
Бренд: Club Car Страницы: 48
Mercedes-Benz 2016 SLK Operator'S Manual preview
2016 SLK
Бренд: Mercedes-Benz Страницы: 358
Thule 1430 Kit Instructions Manual preview
1430 Kit
Бренд: Thule Страницы: 8
Volvo V70XC Cross country 1998 Owner'S Manual preview
V70XC Cross country 1998
Бренд: Volvo Страницы: 262
Great Wall WEY VV5 Service Manual preview
WEY VV5
Бренд: Great Wall Страницы: 18
WIX WP9378 Installation Instruction preview
WP9378
Бренд: WIX Страницы: 2
Oldsmobile Bravada 1997 Owner'S Manual preview
Bravada 1997
Бренд: Oldsmobile Страницы: 358
Yakima K974 Manual preview
K974
Бренд: Yakima Страницы: 11
Toyota 2011 Camry SE V6 Brochure & Specs preview
2011 Camry SE V6
Бренд: Toyota Страницы: 33
Coolster CHALLENGER GK-6125A 2018 Manual preview
CHALLENGER GK-6125A 2018
Бренд: Coolster Страницы: 45
TOGU Airgo Active cushion / Comfort Manual And Maintenance Instructions preview
Airgo Active cushion / Comfort
Бренд: TOGU Страницы: 2
Whispbar K482W Fitting Instructions Manual preview
K482W
Бренд: Whispbar Страницы: 14
T.J.M. T13 Outback Frontal Protection System Fitting Instructions Manual preview
T13 Outback Frontal Protection System
Бренд: T.J.M. Страницы: 18

Бренды по названию

Популярные бренды

Загрузить еще бренды