Ford 2010 Milan Hybrid страница 144 Скачать руководство пользователя | Manualshive

Страница: 144 / 326

background image

The fact that the airbags did not inflate in a collision does not mean that
something is wrong with the system. Rather, it means the forces were
not of the type sufficient to cause activation. Side airbags are designed
to inflate in side-impact collisions, not roll-over, rear-impact, frontal or
near-frontal collisions, unless the collision causes sufficient lateral
deceleration.

WARNING:

Several air bag system components get hot after

inflation. Do not touch them after inflation.

WARNING:

If the side

airbag has deployed,

the

airbag will not function again.
The side airbag system
(including the seat) must be
inspected and serviced by an
authorized dealer.

If the airbag

is not replaced, the unrepaired
area will increase the risk of injury
in a collision.

Determining if the system is operational

The SRS uses a readiness light in the instrument cluster or a tone to
indicate the condition of the system. Refer to the

Airbag readiness

section in the

Instrument Cluster

chapter. Routine maintenance of the

airbag is not required.

Any difficulty with the system is indicated by one or more of the
following:

•

The readiness light (same light as used for front airbag system) will
either flash or stay lit.

•

The readiness light will not illuminate immediately after ignition is
turned to the on position.

•

A series of five beeps will be heard. The tone pattern will repeat
periodically until the problem and light are repaired.

If any of these things happen, even intermittently, have the SRS serviced
at an authorized dealer immediately. Unless serviced, the system may not
function properly in the event of a collision.

2010 Milan

(mln)

Owners Guide, 1st Printing
USA

(fus)

Seating and Safety Restraints

144

«
...
142
143
144
145
146
...
»

Содержание 2010 Milan Hybrid







































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2010 Milan Hybrid

Бренд: NavLinkz Страницы: 4

Бренд: APEXi Страницы: 18

Бренд: Prorack Страницы: 15

Бренд: Whispbar Страницы: 15

Бренд: Honda Страницы: 208

Бренд: Kargo Master Страницы: 6

Бренд: Webasto Страницы: 34

Бренд: NavLinkz Страницы: 21

Бренд: StowAway 2 Страницы: 2

Бренд: Nav TV Страницы: 4

Бренд: ULTIMATE SPEED Страницы: 6

Бренд: Sagem Страницы: 10

ULTIMATE SPEED 296713

Бренд: walser Страницы: 10

Бренд: Mercedes-Benz Страницы: 373

2010 Challenger SRT

Бренд: Dodge Страницы: 444

Бренд: Mopar Страницы: 18

Бренд: Connects2 Страницы: 8

Бренд: Reliant Страницы: 206

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды