manualshive.com logo in svg

Ford 2010 Milan Hybrid, Руководство пользователя

Владельцы Ford 2010 Milan Hybrid могут бесплатно загрузить руководство по эксплуатации на нашем сайте. Узнайте все о своем автомобиле, используя наше руководство. Просто скачайте его с manualshive.com и получите все необходимые сведения для правильного использования и обслуживания вашего автомобиля.

Поделиться
Скачать
background image

Once blockage is removed, the system will require some driving time and
detection of at least two vehicle object prior to realizing it is unblocked,
or the driver can cycle the ignition key. If blocked and the ignition key is
cycled, the system resets to unblocked. If however blockage is still
present after the key cycle, the system will sense again that it is blocked
after driving in traffic.

The following table lists possible causes and actions for this message
being displayed:

The surface of the left or right
radar is dirty or obstructed in
some way

Clean the fascia area in front of
the radar, either left or right side,
or remove obstruction.

The surface of the left or right
radar is not dirty or obstructed

Drive normally in traffic for a few
minutes to allow the radar to
detect that it is no longer blocked.
Note, the vehicle must be in D
(Drive) and a few vehicles must
pass so that the BLIS™ can clear a
blocked state.

Heavy rainfall or heavy snowfall is
interfering with the radar signals

No action required by the driver.
The system will automatically go
unblocked once the
rainfall/snowfall rate decreases or
stops. Do not use BLIS™-CTA in
heavy rainfall or heavy snowfall.

Trailer tow false alerts

When towing a trailer the left and right sensor may detect the trailer
thus causing a false alert. It may be desirable to turn the BLIS™ system
off if the false alerts become annoying.

Day and night brightness

The BLIS™-CTA amber alert will automatically dim when the headlamp
switch is in PARK, ON, or AUTO ON and night time darkness has been
detected by the sun sensor.

ALL WHEEL DRIVE (AWD) SYSTEM (IF EQUIPPED)

Your vehicle may be equipped with a full-time All Wheel Drive (AWD)
system. The AWD system is an active system, meaning it not only
responds to wheel slip between the front and rear axles but also has the
ability to anticipate wheel slip and transfer torque to the rear wheels
before slip occurs. The AWD system is active all the time and requires no
input from the operator.

2010 Milan

(mln)

Owners Guide, 1st Printing
USA

(fus)

Driving

225

Содержание 2010 Milan Hybrid







































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2010 Milan Hybrid

Cadillac ESCALADE - BROCHURE 2009 Personalization Manual preview
ESCALADE - BROCHURE 2009
Бренд: Cadillac Страницы: 24
Cadillac Escalade Personalization Manual preview
Escalade
Бренд: Cadillac Страницы: 20
Cadillac Escalade 2016 Convenience/Personalization Manual preview
Escalade 2016
Бренд: Cadillac Страницы: 20
Vauxhall MOVANO Owner'S Manual preview
MOVANO
Бренд: Vauxhall Страницы: 177
Napoli NPL-TV 7874 DIGITAL Instruction Manual preview
NPL-TV 7874 DIGITAL
Бренд: Napoli Страницы: 20
Audi A4 2016 Quick Questions And Answers preview
A4 2016
Бренд: Audi Страницы: 9
Belkin WIC004 Setting Up preview
WIC004
Бренд: Belkin Страницы: 4
Safe Fleet PRIME DESIGN VRR-E-PM21 Assembly Instructions Manual preview
PRIME DESIGN VRR-E-PM21
Бренд: Safe Fleet Страницы: 12
Cadillac 1999 DeVille Owner'S Manual preview
1999 DeVille
Бренд: Cadillac Страницы: 368
Luverne 205760 Installation Instructions preview
205760
Бренд: Luverne Страницы: 3
Navman B2+ User Manual preview
B2+
Бренд: Navman Страницы: 27
RAM 1500 2WD 2021 Owner'S Manual preview
1500 2WD 2021
Бренд: RAM Страницы: 496
Safe Fleet PRIME DESIGN URX-001-E Manual preview
PRIME DESIGN URX-001-E
Бренд: Safe Fleet Страницы: 8
travall TDG-1301 Fitting Instruction preview
TDG-1301
Бренд: travall Страницы: 2
Gacell 13553 User Manual preview
13553
Бренд: Gacell Страницы: 12
Yakima K896 Instructions Manual preview
K896
Бренд: Yakima Страницы: 12
GReddy 12519101 Instruction Manual preview
12519101
Бренд: GReddy Страницы: 12
Fiat 500L 2020 Owner'S Manual preview
500L 2020
Бренд: Fiat Страницы: 284

Бренды по названию

Популярные бренды

Загрузить еще бренды