Ford 2010 Milan Hybrid страница 98 Скачать руководство пользователя | Manualshive

Страница: 98 / 326

background image

1. Place the key in the ignition and
turn the ignition to the 3 (on)
position.

2. Press the power door unlock
control on the door panel three
times.

3. Turn the ignition from the 3 (on)
position to the 1 (off) position.

4. Press the power door unlock control on the door panel three times.

5. Turn the ignition back to the 3 (on) position. The horn will chirp one
time to confirm programming mode has been entered and is active.

6. Press the power door unlock control twice within five seconds.

Note:

The horn will chirp once to indicate the perimeter lighting feature

has been deactivated. The horn will chirp once and honk once (one short
and one long) to indicate the perimeter lighting feature has been
activated.

7. Turn the ignition to the 1 (off) position to exit the procedure.

Note:

The horn will chirp once to confirm the procedure is complete.

Illuminated exit

•

When all vehicle doors are closed and the key is removed from the
ignition, the interior dome lamps (and the exterior mirror puddle
lamps, if equipped) will illuminate.

The lights will turn off if all the doors remain closed and

•

25 seconds elapse, or

•

the key is inserted in the ignition.

Battery saver

The battery saver will shut off the interior lamps 30 minutes after the
ignition has been turned to the 1 (off) position.

•

If the dome lamps were turned on using the panel dimmer control, the
battery saver will shut them off 30 minutes after the ignition has been
turned to the 1 (off) position.

•

If the courtesy lamps were turned on because one of the vehicle doors
or the trunk was opened, the battery saver will shut off them off
10 minutes after the ignition has been turned to the 1 (off) position.

•

The battery saver will shut off the headlamps 10 minutes after the
ignition has been turned to the 1 (off) position.

2010 Milan

(mln)

Owners Guide, 1st Printing
USA

(fus)

Locks and Security

98

«
...
96
97
98
99
100
...
»

Содержание 2010 Milan Hybrid







































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2010 Milan Hybrid

Бренд: Falcon Страницы: 8

Бренд: Dodge Страницы: 24

Бренд: Motoalliance Страницы: 8

Бренд: Cadillac Страницы: 34

Бренд: Prorack Страницы: 10

Бренд: Ranger design Страницы: 24

Бренд: Camoplast Страницы: 19

Бренд: Joie Страницы: 53

Бренд: Webasto Страницы: 23

PRIME DESIGN VRR3-FT21G-ST

Бренд: Safe Fleet Страницы: 12

2013 2500 Big Horn

Бренд: RAM Страницы: 12

Бренд: MMD Страницы: 3

Бренд: Brainz Страницы: 2

Бренд: Reese Страницы: 21

2013 Zafira Tourer

Бренд: Vauxhall Страницы: 289

Бренд: Camcar Страницы: 2

Бренд: walser Страницы: 8

Бренд: Honda Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды