Ford 1998 F-150 Скачать руководство пользователя страница 48

Страница: 48 / 74

normal operation.

REPAIR circuit 764 (BR/W). CLEAR the DTCs. CYCLE the ignition OFF then ON. TEST the
system for normal operation.

B47

CHECK CIRCUIT 764 (BR/W) FOR OPEN

GEM C241

Measure the resistance between transfer case assembly C201-9, circuit 764 (BR/W), and

GEM C241-19, circuit 764 (BR/W).

Is the resistance less than 5 ohms?

Yes

GO to

B48

REPAIR circuit 764 (BR/W). CLEAR the DTCs. TEST the system for normal operation.

B48

CHECK CIRCUIT 764 (BR/W) FOR SHORT TO POWER

Measure the voltage between transfer case assembly C201-9, circuit 764 (BR/W), and

ground.

Is any voltage indicated?

Yes

REPAIR circuit 764 (BR/W). CLEAR the DTCs. CYCLE the ignition OFF then ON. TEST the
system for normal operation.

REPLACE the GEM; REFER to

Section 419-10

. CLEAR the DTCs. TEST the system for

normal operation.

B49

MONITOR THE GEM PID PLATE_D FOR OPEN

Monitor the GEM PID PLATE_D.

Does the GEM PID PLATE_D not indicate OPEN?

Yes

GO to

B51

Page 48 of 74

1998 F-150/250 Workshop Manual

1/11/2011

http://www.fordtechservice.dealerconnection.com/pubs/con...

Содержание 1998 F-150











































































Результаты поиска

Содержание 1998 F-150

Отзывы:

Бренды по названию

Популярные бренды

Ford 1998 F-150, Руководство по ремонту

Результаты поиска

Содержание 1998 F-150

Отзывы:

Бренды по названию

Популярные бренды