Ford 1998 F-150 Скачать руководство пользователя

Страница: 42 / 74

REPLACE the vehicle speed sensor; REFER to

Section 303-14

. CLEAR the DTCs. TEST the

system for normal operation.

REPLACE the fuse junction panel. CLEAR the DTCs. TEST the system for normal operation.

B31

CHECK THE CONTACT PLATE SWITCHES — MONITOR THE GEM PIDS PLATE_A, PLATE_B, PLATE_C, AND PLATE_D

Monitor GEM PIDs PLATE_A, PLATE_B, PLATE_C, and PLATE_D.

Place the mode switch in the 4H position and record the PIDs.

Place the mode switch in the 4L position and record the PIDs.

Compare the GEM PIDs with Table 4—Contact Plate Sensor Position Codes; refer to 4WD

Tables.

Do the GEM PIDs agree with Table 4?

Yes

REPAIR the transfer case or shift motor assembly. REFER to

Section 308-07B

. CLEAR the

DTCs. TEST the system for normal operation.

GO to

B32

B32

MONITOR THE GEM PID PLATE_A FOR OPEN

Transfer Case Assembly C201

Trigger the GEM active command PLATE POWER to ON.

Monitor the GEM PID PLATE_A.

Page 42 of 74

1998 F-150/250 Workshop Manual

1/11/2011

http://www.fordtechservice.dealerconnection.com/pubs/con...

Содержание 1998 F-150











































































Результаты поиска

Содержание 1998 F-150

Отзывы:

Похожие инструкции для 1998 F-150

Бренды по названию

Популярные бренды

Ford 1998 F-150, Руководство по ремонту

Результаты поиска

Содержание 1998 F-150

Отзывы:

Похожие инструкции для 1998 F-150

Бренды по названию

Популярные бренды