Ford 1998 F-150 Скачать руководство пользователя

Страница: 71 / 74

turning the ignition switch to START.

Monitor the GEM PID IGN_GEM while turning the ignition switch through the START, RUN,
OFF, and ACC positions.

Do the PID values agree with the ignition switch positions?

Yes

GO to

REPAIR the ignition circuit (RUN/ACC: circuit 297 [BK/LG], RUN: circuit 1040 [R/LB], START:
circuit 32 [R/LB] or circuit 481 [GY/Y] in question. CLEAR the DTCs. TEST the system for
normal operation.

CHECK FUSE JUNCTION PANEL FUSE 15 (5A) AND POWER DISTRIBUTION BOX FUSE 22 (50A)

Fuse 15 (5A)

Fuse 22 (50A)

Are the fuses OK?

Yes

GO to

CHECK CIRCUIT 1052 (T/BK) FOR VOLTAGE

Fuse Junction Panel C243

Measure the voltage between fuse junction panel C243-11, circuit 1052 (T/BK), and ground.

Is the voltage greater than 10 volts?

Yes

GO to

REPAIR circuit 1052 (T/BK). CLEAR the DTCs. TEST the system for normal operation.

CHECK FUSE JUNCTION PANEL FOR VOLTAGE

Page 71 of 74

1998 F-150/250 Workshop Manual

1/11/2011

http://www.fordtechservice.dealerconnection.com/pubs/con...

Содержание 1998 F-150











































































Результаты поиска

Содержание 1998 F-150

Отзывы:

Похожие инструкции для 1998 F-150

Бренды по названию

Популярные бренды

Ford 1998 F-150, Руководство по ремонту

Результаты поиска

Содержание 1998 F-150

Отзывы:

Похожие инструкции для 1998 F-150

Бренды по названию

Популярные бренды