Ford 1998 F-150 Скачать руководство пользователя

Страница: 62 / 74

If the PID displays OFFO-G and lamp stays on continuously, GO to

If the PID displays OFFO-G and the lamp does not illuminate, REFER to

Section 413-01A

CHECK THE GEM FOR SHORT TO GROUND

GEM C241

Is the lamp still illuminated?

Yes

GO to

REPLACE the GEM; REFER to

Section 419-10

. CLEAR the DTCs. TEST the system for

normal operation.

CHECK CIRCUITS 210 (LB) AND 975 (BR/Y) FOR SHORT TO GROUND

Instrument Cluster C236

Measure the resistance between:

4x4 HIGH: GEM C241-9, circuit 210 (LB), and ground.

4x4 LOW: GEM C241-10, circuit 975 (BR/Y), and ground.

Are the resistances greater than 10,000 ohms?

Yes

REPAIR the instrument cluster. CLEAR the DTCs. TEST the system for normal operation.

REPAIR circuit 210 (LB) and/or 975 (BR/Y). CLEAR the DTCs. TEST the system for normal
operation.

CHECK CIRCUITS 210 (LB) AND 975 (BR/Y) FOR SHORT TO POWER

Instrument Cluster C236

Page 62 of 74

1998 F-150/250 Workshop Manual

1/11/2011

http://www.fordtechservice.dealerconnection.com/pubs/con...

Содержание 1998 F-150











































































Результаты поиска

Содержание 1998 F-150

Отзывы:

Похожие инструкции для 1998 F-150

Бренды по названию

Популярные бренды

Ford 1998 F-150, Руководство по ремонту

Результаты поиска

Содержание 1998 F-150

Отзывы:

Похожие инструкции для 1998 F-150

Бренды по названию

Популярные бренды