Ford 1998 F-150 Скачать руководство пользователя страница 14

Страница: 14 / 74

Is the axle disconnect working properly?

Yes

EXIT the active command mode; GO to

A21

GO to

Pinpoint Test C

A21

CHECK THE FRONT DRIVESHAFT ENGAGEMENT

Place the mode switch in the 4H position.

Verify the front and rear driveshafts both spin.

Is the transfer case locking the front driveshaft to the rear driveshaft?

Yes

GO to

A22

GO to

A24

A22

CHECK THE FRONT DRIVESHAFT DISENGAGEMENT

NOTE:

When 4WD is disengaged, the front driveshaft may spin due to viscous drag in the

transfer case, especially if cold. If this occurs, the front driveline can easily be stopped.

Place the mode switch in the 2H position. Only the rear driveshaft should spin.

Does only the rear driveshaft spin?

Yes

GO to

A23

GO to

A24

A23

CHECK THE FRONT AXLE DISENGAGEMENT

Trigger the GEM active commands AXLE ENGG to OFF and AXLE DSCN to ON.

Spin one front tire and the other front tire should not spin.

Is the axle disconnect working properly?

Yes

The 4WD system is working properly.

GO to

Pinpoint Test C

Page 14 of 74

1998 F-150/250 Workshop Manual

1/11/2011

http://www.fordtechservice.dealerconnection.com/pubs/con...

Содержание 1998 F-150











































































Результаты поиска

Содержание 1998 F-150

Отзывы:

Бренды по названию

Популярные бренды

Ford 1998 F-150, Руководство по ремонту

Результаты поиска

Содержание 1998 F-150

Отзывы:

Бренды по названию

Популярные бренды