Ford 1998 F-150 Скачать руководство пользователя

Страница: 13 / 74

REPLACE circuit 682 (DB). CLEAR the DTCs. TEST the system for normal operation.

A18

CHECK CIRCUIT 682 (DB) FOR SHORT TO GROUND

Multi-Function Switch C259

Measure the resistance between mode switch C230-2, circuit 682 (DB), and ground.

Is the resistance greater than 10,000 ohms?

Yes

GO to

A19

REPAIR circuit 682 (DB). CLEAR the DTCs. TEST the system for normal operation.

A19

CHECK CIRCUIT 682 (DB) FOR SHORT TO POWER

Measure the voltage between mode switch C230-2, circuit 682 (DB), and ground.

Is any voltage indicated?

Yes

REPAIR circuit 682 (DB). CLEAR the DTCs. TEST the system for normal operation.

REPLACE the GEM; REFER to

Section 419-10

. CLEAR the DTCs. TEST the system for

normal operation.

A20

CHECK THE FRONT AXLE ENGAGEMENT

Trigger the GEM active commands AXLE ENGG to ON and AXLE DSCN to OFF and drive a

short distance.

Raise and support the vehicle with the engine running; refer to

Section 100-02

Spin one front tire. The other tire should spin in the opposite direction.

Page 13 of 74

1998 F-150/250 Workshop Manual

1/11/2011

http://www.fordtechservice.dealerconnection.com/pubs/con...

Содержание 1998 F-150











































































Результаты поиска

Содержание 1998 F-150

Отзывы:

Похожие инструкции для 1998 F-150

Бренды по названию

Популярные бренды

Ford 1998 F-150, Руководство по ремонту

Результаты поиска

Содержание 1998 F-150

Отзывы:

Похожие инструкции для 1998 F-150

Бренды по названию

Популярные бренды