Ford 1998 F-150 страница 20 Скачать руководство пользователя

Страница: 20 / 74

Are the resistances less than 5 ohms?

Yes

RECONNECT the transfer case assembly. GO to

A41

GO to

A40

A38

CHECK CIRCUIT 777 (Y) FOR OPEN

Measure the resistance between transfer case shift relays C221-7, circuit 777 (Y), and

transfer case assembly C201-15, circuit 777 (Y).

Is the resistance less than 5 ohms?

Yes

GO to

A39

REPAIR circuit 777 (Y). CLEAR the DTCs. TEST the system for normal operation.

A39

CHECK CIRCUIT 778 (O) FOR OPEN

Measure the resistance between transfer case shift relays C221-10, circuit 778 (O), and

transfer case assembly C201-14, circuit 778 (O).

Is the resistance less than 5 ohms?

Yes

REPLACE the transfer case shift relays. CLEAR the DTCs. TEST the system for normal
operation.

REPAIR circuit 778 (O). CLEAR the DTCs. TEST the system for normal operation.

A40

CHECK THE GROUND TO THE TRANSFER CASE SHIFT RELAYS — CIRCUIT 57 (BK)

Transfer Case Shift Relays C221

Page 20 of 74

1998 F-150/250 Workshop Manual

1/11/2011

http://www.fordtechservice.dealerconnection.com/pubs/con...

Содержание 1998 F-150











































































Результаты поиска

Содержание 1998 F-150

Отзывы:

Похожие инструкции для 1998 F-150

Бренды по названию

Популярные бренды

Ford 1998 F-150, Руководство по ремонту

Результаты поиска

Содержание 1998 F-150

Отзывы:

Похожие инструкции для 1998 F-150

Бренды по названию

Популярные бренды