Fondital CAPRI C, Инструкция по эксплуатации и обслуживанию

Страница: 7 / 24

1.2.3 Boiler shutdown
When the boiler malfunctions, the burner is automatically shu-
tdown.
Please, see the troubleshooting section (paragraph 7. “Trouble-
shooting”) in this manual, for possible shutdown cause detection.
1.2.3.1 Burner shutdown
When there is a burner malfunction, it automatically shuts down
and light 7 comes on, in which case proceed as follows:
- First check there is sufficient fuel by checking that the fuel inter-
ception valve is open and that there is fuel in the network;
- Then unhook the front panel of the boiler by pulling it outwards,
lift it in order to remove it from the boiler itself and unblock the
burner by pressing the lit up red unblocking button (pic. 2); if the
appliance does not start up or blocks again, at the third attempt
contact qualified professionals for servicing.
Do the same if the burner shuts down frequently, as there is
obviously a recurring fault.
1.2.3.2 Shutdown due to overheating
Should the overheating red light
2
(pic. 1) come on, signalling the
safety thermostat intervention due to a malfunction, contact an
Authorized Service Centre or qualified personnel for service.
1.2.3.3 Shutdown due to insufficient water pressure
In the event of boiler shutdown due to water pressure switch inter-
vention, no. 4 red light starts blinking, signalling insufficient water
pressure in the CH system.
In order to restore water pressure, proceed as follows (see pic. 4):
- set the general switch 16 (pic. 1) to 0 (the green light turns off);
- unhook the front panel of the boiler by pulling it outwards and lift
it in order to remove it from the boiler itself;
- turn the knob of the loading valve (pic. 2) in an anti-clockwise
direction to let the water into the unit and keep it open until the
manometer (14 pic. 1) indicates that the pressure value of 1÷1,3
bar has been reached; at this stage close the valve by turning the
knob in a clockwise direction and replace the front panel.
WARNING
Only the loading valve should be actuated. Do not touch any
other part of the unit that could scald, such as the heat exchan-
ger or the water pipes.
Once the loading procedure is completed, fully close the inlet
tap. Should the tap not be properly closed, as pressure increa-
ses, boiler CH safety valve may open and water flow out.
Should boiler frequently shut down due to insufficient water pres
-
sure, have it serviced by an Authorized Service Centre or qua-
lified personnel.
1.2.3.4 Shutdown due to malfunction of temperature probes
Should the burner shut down due to malfunctioning of temperatu-
re probes, the following lights turn on and flash:
- red light 5 (pic.1) for probe 1 (CH)
- red light 7 for probe 2 (water tank)
In this instance, contact an Authorized Service Centre or qualified
personnel for service.
1.3 Maintenance
It is necessary to service the boiler periodically, according
to the schedule indicated in the applicable section of this
manual.
Correct maintenance allows for efficient and correct functio-
ning of the equipment, granting the better working conditions,
optimizing performance and safety for people, animals, things
and environment.
The user may only clean the external boiler casing, by means
of commonly marketed household products.
Do not use water!
As provided, the boiler is to be serviced once a year. Correct
maintenance ensures boiler to function efficiently, environmentally
friendly, preventing any danger to people, animals or property.
Only qualified personnel are lawfully allowed to service the boiler.
The manufacturer recommends Customers to contact an Authori-
zed Service Centre for maintenance and repairs.
1.4
Information for the user
The user may only access boiler parts that can be reached
without using technical equipment and/or tools: no one, inclu-
ding qualified personnel, is authorized to modify the boiler.
The manufacturer shall not be held responsible for damage to
people, animals, or property, due to tampering with the boiler
or improper intervention.
Should the boiler be left inactive for a long time and power
main supply disconnected, it might be necessary to unlock
the pump.
Pump service therefore only qualified personnel may perform
it.
Pump blockage may be avoided by mixing to water, filming
additives suitable for multi-metal systems.
CH system can be properly protected from frost by using spe-
cific anti-frost additives suitable for multi-metal systems. Do
not use automotive products and verify the additive efficiency
over time.
The boiler is equipped with a thermometer allowing for water
temperature verification.
Reset button
Filling tap
pic. 2
7