Foerster TAK5-CH1-25 Скачать руководство пользователя страница 175

Страница: 175 / 226

Failures and warnings

175

Increasing/reducing the electrode sensitivity

12.1.6

Water meter

This failure message is displayed if during water dispense

•

the supply electrode is grounded,

•

but the water meter does not transmit any pulses.

The water meter should be checked and replaced, if necessary,

service personnel

. Feeding can be carried on as an emer-

gency operation.

1. In

water HE start?

press

, then in

water bo. start?

press

and check whether the pulses are displayed.

2. In

mixer emptying?

press

3. Confirm

delete failure?

with

4. Confirm

emergency operation start?

with

5. The warning

water meter

will be displayed. At the same time,

the calibration values for boiler water become invalid. The fail-

ure message on the right will be displayed.

6. Calibrate

water bo(iler)

and

water HE

. After that, the failure

message will disappear. The automatic feeder will start the

emergency operation.

7. If the water meter works properly again or has been re-

placed, delete the warning

water meter.

The failure messag-

Danger!

Hazardous voltage! Pull the mains

plug.

To increase the sensitivity of the electrode,

turn the potentiometer (see wiring diagram) lo-

cated on the motherboard clockwise. To de-

crease the sensitivity of the electrode, turn the

potentiometer counterclockwise.

failure

water meter

failure

pulses:

water HE: start?

water bo.: start?

emergency operation

start?

failure

calibration

Содержание TAK5-CH1-25



































































































































































































































Результаты поиска

Содержание TAK5-CH1-25

Отзывы:

Бренды по названию

Популярные бренды

Foerster TAK5-CH1-25, Инструкция по эксплуатации

Результаты поиска

Содержание TAK5-CH1-25

Отзывы:

Бренды по названию

Популярные бренды