Foerster TAK5-CH1-25 Скачать руководство пользователя страница 173

Страница: 173 / 226

Failures and warnings

173

If there is no explanation for the failure, service personnel should

check the automatic feeder for lime deposits resp. other sources

for defect.

The failure message on the right is displayed:

> Check the heating.

> Also check the temperature value in the mixer for

min. temp.

12.1.3

Temperature too high

If the temperature of the boiler water is too high, the failure mes-

sage on the right will be displayed.

1. Press

to check the temperature.

2. In

water bo. start?

keep

pressed. Drain the boiler water

into the mixer until the displayed failure message disappears.

3. To empty the mixer, in

mixer: empty?

press

If you provide the boiler with pre-heated water, please check

whether the temperature of the supplied water is too high.

If there is no explanation for the failure, let service personnel

check the automatic feeder.

12.1.4

Heat exchanger not filled

At start-up of the automatic feeder the control checks whether

the heat exchanger is filled with water. If this check fails, feeding

will be broken off.

1. Check the water supply.

2. In

HE fill?

press

3. Check whether the

supply electrode resp. the

bar elec-

trode is touched by the water jet during heat exchanger filling

and the display shows „covered“.

4. Check, if necessary, whether the

supply resp. the

bar

electrode are touched by the water jet when pressing

water bo. start?

failure

heating xx.x

failure

temperature too high

boiler: xx.x

water bo.: start?

mixer: empty?

failure

HE not filled

HE: fill?

mixer: empty?

water HE: start?

Содержание TAK5-CH1-25



































































































































































































































Результаты поиска

Содержание TAK5-CH1-25

Отзывы:

Похожие инструкции для TAK5-CH1-25

Бренды по названию

Популярные бренды

Foerster TAK5-CH1-25, Инструкция по эксплуатации

Результаты поиска

Содержание TAK5-CH1-25

Отзывы:

Похожие инструкции для TAK5-CH1-25

Бренды по названию

Популярные бренды