Fluke ScopeMeter 190 Series III Скачать руководство пользователя страница 41

Страница: 41 / 70

ScopeMeter® Test Tool

Calibration Adjustment

Display Messages and Key Functions

When the Test Tool is in the calibration mode, only the

softkeys, the

key, and the

key are active, unless otherwise stated.

The calibration adjustment menu shows the actual calibration step (name and number) and its

status:

Cal Name (CL nnnn) %:Status (…)

Note

and

are disabled whenever they can harm the process.

Cal Name

Name of the selected calibration step, for example, WarmingUp

(CL nnnn)

Number of the calibration step

Progress %

Status (…) can be:

IDLE (valid)

After (re)entering this step, the calibration process is not started. The calibration

data of this step are valid. This means that the last time this step was done, the

calibration was successful. It does not necessarily mean that the unit meets the

specifications related to this step.

IDLE (invalid)

After (re)entering this step, the calibration process is not started. The calibration

data are invalid. This means that the last time this step was done, the calibration was

not successful. Most probably the unit will not meet the specifications if the actual

calibration data are saved.

BUSY aaa%

bbb%

Calibration adjustment step in progress; progress % for Input A and Input B. During

Warming-Up, the elapsed time is shown.

READY

Calibration adjustment step finished.

Error :xxxx

Calibration adjustment failed, due to wrong input signal(s) or because the Test Tool is

defective.
If the error code is <5000 you can repeat the failed step.
If the error code is

≥

5000 you must repeat the complete final calibration (start at

Warming-Up 2, Warm-Up Final, and ADC Timing

The functions of the keys are:

PREVIOUS

select the previous step (if applicable)

NEXT

select the next step (if applicable)

CALIBRATE

start the calibration adjustment of the actual step

EXIT

leave the calibration mode (turn off and turn on the

tool to make sure that the tool operation is normal)

Содержание ScopeMeter 190 Series III







































































Результаты поиска

Содержание ScopeMeter 190 Series III

Отзывы:

Похожие инструкции для ScopeMeter 190 Series III

Бренды по названию

Популярные бренды

Fluke ScopeMeter 190 Series III, Руководство по обслуживанию

Результаты поиска

Содержание ScopeMeter 190 Series III

Отзывы:

Похожие инструкции для ScopeMeter 190 Series III

Бренды по названию

Популярные бренды