FlowLine DataView LI55 Скачать руководство пользователя страница 27

Страница: 27 / 32

DataView™ LI55 Level Controller

Quick Start

| P a g e

To set the Repeater / Analog Output:
Note:

Before configuring the Analog Output, make sure the Scale has

been completed.

1. Press

the

MENU

button to enter the Main Menu. Units (unitS) will

be the first operation available.

2. Press

the

button to scroll through the menu options until you

reach Analog Output (Aout).

3. Press

ENTER

button to enter Analog output. Empty (EmPtY) will

appear.

4. Press

the

ENTER

button to change the Empty value.

a. Press the Right button to move the highlighted digit to the

right and the Up button to increase the setting's value.

5. Press

ENTER

button to save the settings.

a. Full

(FuLL)

will

appear.

6. Press

ENTER

button to move the highlighted digit to the right and

the Up button to increase the setting's value.

7. Press

ENTER

button again to save the settings.

8. Press

the

MENU

button to exit.

Содержание DataView LI55

































Результаты поиска

Содержание DataView LI55

Отзывы:

Похожие инструкции для DataView LI55

Бренды по названию

Популярные бренды

FlowLine DataView LI55, Быстрый старт

Результаты поиска

Содержание DataView LI55

Отзывы:

Похожие инструкции для DataView LI55

Бренды по названию

Популярные бренды