background image

 

QS301033 Rev C | LIM6000FL_BX11 

SFT039 Ver 3.100 & up 

08/12 

For complete product documentation, video training, and 
technical support, go to www.flowline.com. 

 

For phone support, call 562-598-3015 
from 8am to 5pm PST, Mon - Fri. 
(Please have the Part and Serial number available.) 

Warranty 

 

Flowline warrants to the original purchaser of its products that such products will be free from 
defects in material and workmanship under normal use and service in accordance with 
instructions furnished by Flowline for a period, which is equal to the shorter of one year from 
the date of purchase of such products or two years from the date of manufacture of such 
products. Flowline's obligation under this warranty is solely and exclusively limited to the 
repair or replacement, at Flowline's option, of the products or components, which Flowline's 
examination determines to its satisfaction to be defective in material or workmanship within 
the warranty period. Flowline must be notified pursuant to the instructions below of any claim 
under this warranty within thirty (30) days of any claimed lack of conformity of the product. 
Any product repaired or replaced under this warranty will be warranted only for the remainder 
of the original warranty period.  

Returns 

 

Products cannot be returned to Flowline without Flowline's prior authorization. To return a 
product that is thought to be defective, go to www.flowline.com, and submit a customer 
return (MRA) request form and follow the instructions therein. All warranty and non-warranty 
product returns to Flowline must be shipped prepaid and insured. Flowline will not be 
responsible for any products lost or damaged in shipment.  

Limitations 

 

This warranty does not apply to products which: 1) are beyond the warranty period or are 
products for which the original purchaser does not follow the warranty procedures outlined 
above; 2) have been subjected to electrical, mechanical or chemical damage due to 
improper, accidental or negligent use; 3) have been modified or altered; 4) anyone other than 
service personnel authorized by Flowline have attempted to repair; 5) have been involved in 
accidents or natural disasters; or 6) are damaged during return shipment to Flowline. 
Flowline reserves the right to unilaterally waive this warranty and dispose of any product 
returned to Flowline where: 1) there is evidence of a potentially hazardous material present 
with the product; or 2) the product has remained unclaimed at Flowline for more than 30 
days after Flowline has dutifully requested disposition. This warranty contains the sole 
express warranty made by Flowline in connection with its products. ALL IMPLIED 
WARRANTIES, INCLUDING WITHOUT LIMITATION, THE WARRANTIES OF 
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSLY 
DISCLAIMED. The remedies of repair or replacement as stated above are the exclusive 
remedies for the breach of this warranty. IN NO EVENT SHALL FLOWLINE BE LIABLE FOR 
ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING 
PERSONAL OR REAL PROPERTY OR FOR INJURY TO ANY PERSON. THIS 
WARRANTY CONSTITUTES THE FINAL, COMPLETE AND EXCLUSIVE STATEMENT OF 
WARRANTY TERMS AND NO PERSON IS AUTHORIZED TO MAKE ANY OTHER 
WARRANTIES OR REPRESENTATIONS ON BEHALF OF FLOWLINE. This warranty will 
be interpreted pursuant to the laws of the State of California. If any portion of this warranty is 
held to be invalid or unenforceable for any reason, such finding will not invalidate any other 
provision of this warranty. 

   

   

 

Содержание DataView LI55

































Отзывы: