manualshive.com logo in svg

FlowLine DataView LI55, Быстрый старт, Страница: 31 / 32

Поделиться
Скачать
FlowLine DataView LI55 Скачать руководство пользователя страница 31

DataView™ LI55 Level Controller  

Quick Start 

 31

  |  P a g e

 

Reset Meter to Factory Defaults 

When the parameters have been changed in a way that is difficult to 
determine what’s happening, it might be better to start the setup 
process from the factory defaults. 

 

Instructions to load factory defaults: 

1.  Press and hold 

MENU

 button for 5 seconds to enter the Full Main 

menu. 

Setup

 will appear on the display. 

2.  Press and hold 

MENU

 button again for 3 seconds to enter 

Advanced menu. 

filter

 will appear on the display. 

3. Press 

Up 

button to go to 

diag

 (

Diagnostics

 menu) 

4.  Press and hold 

Right 

button for three seconds, until 

reset

 appears

. 

Press ENTER when display flashes 

rESEt

. 

a. Note: 

If 

ENTER

 is not pressed within three seconds, the 

display returns to the 

Diagnostics

 menu. 

5.  The meter goes through an initialization sequence (similar as on 

power-up), and loads the factory default settings. 

 

  

Содержание DataView LI55

































Отзывы:

Нет отзывов