FläktGroup ECO SIDE Скачать руководство пользователя

Страница: 44 / 48

eCO Side - Installation and Maintenance Manual

FläktGroup DC_10176GB_20180924_R3

Specifications are subject to alteration without notice

13. MAINTENANCE

MAINTENANCE

Make an inspection and if necessary clean the fan according to
Service Schedule, section 13.8..

13.7 FANS

Important! Turn off the safety switch

and wait for the impeller to stop before

inspection and service.

CLEANING

The best way to clean the impeller is to use a vacuum cleaner
attached with a soft dusting brush. To prevent imbalance, clean
all fan blades carefully. After the cleaning check that the fan runs
without vibrations.

PRECAUTIONS BEFORE STARTUP

Before startup, check that the impeller rotates freely and that
there are no foreign objects which could be drawn into and
damage the fan.

LUBRICATING THE FAN MOTOR

The fan motor bearings are factory lubricated and maintenance
free.

REMOVAL OF FAN

1. Disconnect the control cable with fittings.

2. Remove the nuts from the fan.

3. Remove the fan.

Содержание ECO SIDE

















































Результаты поиска

Содержание ECO SIDE

Отзывы:

Похожие инструкции для ECO SIDE

Бренды по названию

Популярные бренды

FläktGroup ECO SIDE, Руководство по установке и обслуживанию

Результаты поиска

Содержание ECO SIDE

Отзывы:

Похожие инструкции для ECO SIDE

Бренды по названию

Популярные бренды