Fisher Minute Mount 2 system Скачать руководство пользователя страница 66

Страница: 66 / 112

Lit. No. 44224, Rev. 14

August 15, 2011

OPERATING YOUR SNOWPLOW

SNOWPLOW HEADLAMP CHECK

With all electrical plugs connected, check the
operation of vehicle and snowplow headlamps.

Lights

Results

Parking Lamps

Both vehicle and snowplow

lamps should be ON.

Right Turn Signal

Both vehicle and snowplow

lamps should be ON.

Left Turn Signal

Both vehicle and snowplow

lamps should be ON.

Connecting and disconnecting the electrical plugs
should switch between the vehicle and snowplow
headlamps as follows:

• Electrical plugs DISCONNECTED – Vehicle

headlamps function normally.

• Electrical plugs CONNECTED – Vehicle

headlamp functions transfer to the snowplow
headlamps. On some DRL systems, both the
vehicle and snowplow headlamps will function.

Aiming the Headlamps

• Aim the snowplow headlamps with the

snowplow mounted and raised in the transport
position. See Aiming Headlamp Beams in the
Maintenance section for instructions.

• Aim the vehicle headlamps with the snowplow

removed from the vehicle.

Содержание Minute Mount 2 system

















































































































Результаты поиска

Содержание Minute Mount 2 system

Отзывы:

Похожие инструкции для Minute Mount 2 system

Бренды по названию

Популярные бренды

Fisher Minute Mount 2 system, Руководство пользователя

Результаты поиска

Содержание Minute Mount 2 system

Отзывы:

Похожие инструкции для Minute Mount 2 system

Бренды по названию

Популярные бренды