Fisher Minute Mount 2 system Скачать руководство пользователя страница 78

Страница: 78 / 112

Lit. No. 44224, Rev. 14

August 15, 2011

NOTE: Only the driver should be in the vehicle
cab when the snowplow is attached.

OPERATING YOUR SNOWPLOW

CAUTION

Never stack snow with the blade angled.
This could damage the snowplow or the
vehicle bumper.

CAUTION

Plowing speed should not exceed 10 mph
(16 km/h).

General Instructions

1. Before plowing, make sure you know of any

obstructions hidden beneath the snow such as
bumper stops in parking lots, curbs, sidewalk
edges, shrubs, fences or pipes sticking up
from the ground. If unfamiliar with the area to
be plowed, have someone familiar with the
area point out obstacles.

2. If possible and you have good visibility, plow

during the storm rather than letting snow
accumulate.

3. Do not exceed 10 mph (16 km/h) when

plowing snow.

4. When you are stacking snow, begin raising

the blade as you come close to the stack. This
will let the blade ride up the stack.

Содержание Minute Mount 2 system

















































































































Результаты поиска

Содержание Minute Mount 2 system

Отзывы:

Похожие инструкции для Minute Mount 2 system

Бренды по названию

Популярные бренды

Fisher Minute Mount 2 system, Руководство пользователя

Результаты поиска

Содержание Minute Mount 2 system

Отзывы:

Похожие инструкции для Minute Mount 2 system

Бренды по названию

Популярные бренды