Fisher Minute Mount 2 system Скачать руководство пользователя страница 12

Страница: 12 / 112

Lit. No. 44224, Rev. 14

August 15, 2011

SAFETY

PERSONAL SAFETY

• Remove ignition key and put the vehicle in

park or in gear to prevent others from starting
the vehicle during installation or service.

• Wear only snug-

tting clothing while working

on your vehicle or snowplow.

• Do not wear jewelry or a necktie, and secure

long hair.

• Wear safety goggles to protect your eyes from

battery acid, gasoline, dirt and dust.

• Avoid touching hot surfaces such as the

engine, radiator, hoses and exhaust pipes.

• Always have a

re extinguisher rated BC

handy, for

ammable liquids and electrical

res.

FIRE AND EXPLOSION

Be careful when using gasoline. Do not use
gasoline to clean parts. Store only in approved
containers away from sources of heat or

ame.

CELL PHONES

A driver's

rst responsibility is the safe operation

of the vehicle. The most important thing you can
do to prevent a crash is to avoid distractions and
pay attention to the road. Wait until it is safe to
operate Mobile Communication Equipment such
as cell phones or two-way radios.

WARNING

Gasoline is highly

ammable and gasoline

vapor is explosive. Never smoke while
working on vehicle. Keep all open

ames

away from gasoline tank and lines. Wipe
up any spilled gasoline immediately.

Содержание Minute Mount 2 system

















































































































Результаты поиска

Содержание Minute Mount 2 system

Отзывы:

Похожие инструкции для Minute Mount 2 system

Бренды по названию

Популярные бренды

Fisher Minute Mount 2 system, Руководство пользователя

Результаты поиска

Содержание Minute Mount 2 system

Отзывы:

Похожие инструкции для Minute Mount 2 system

Бренды по названию

Популярные бренды