Fisher Minute Mount 2 system Скачать руководство пользователя страница 74

Страница: 74 / 112

Lit. No. 44224, Rev. 14

August 15, 2011

OPERATING YOUR SNOWPLOW

10. If the hydraulic pressure reading is less than

350 psi, increase the pressure by turning the
scrape lock valve stem clockwise 1/4 turn and
retest pressure.

NOTE: Adjustments should be made in
1/4-turn increments.

11. Repeat Steps 9 and 10 until the recommended

pressure (350 psi) is obtained.

NOTE: Adjusting the scrape lock pressure
in excess of the recommended pressure will
increase amp draw and will shorten the life of
the plow motor.

12. Once the recommended pressure is obtained,

lower the blade completely and turn the
control OFF. Turn the vehicle ignition to the
"OFF" position.

13. Disconnect the snowplow battery cable from

the vehicle battery cable.

14. Loosen the breather/

ll plug slowly to relieve

any pressure in the reservoir.

15. Remove the hydraulic testing "Tee"

tting and

gauge from the lift ram base hose.

16. Reconnect the lift ram base hose and tighten

securely.

17. Check the hydraulic

uid level and add if

necessary.

18. Retighten the breather/

ll plug.

19. Replace the hydraulic unit cover.

CAUTION

Do not mix different kinds of hydraulic

uid. Some

uids are not compatible and

may cause performance problems and
product damage.

Содержание Minute Mount 2 system

















































































































Результаты поиска

Содержание Minute Mount 2 system

Отзывы:

Похожие инструкции для Minute Mount 2 system

Бренды по названию

Популярные бренды

Fisher Minute Mount 2 system, Руководство пользователя

Результаты поиска

Содержание Minute Mount 2 system

Отзывы:

Похожие инструкции для Minute Mount 2 system

Бренды по названию

Популярные бренды