Fisher Minute Mount 2 system Скачать руководство пользователя страница 75

Страница: 75 / 112

Lit. No. 44224, Rev. 14

August 15, 2011

OPERATING YOUR SNOWPLOW

NOTE: Always transport the XLS™ snowplow
with both wings fully retracted.

1. Completely raise the blade.

2. Adjust the blade height for maximum

snowplow headlamp illumination.

3. Adjust the blade to the straight position.

4. Turn the control OFF to lock the blade in

place.

NOTE: Overheating is unlikely under normal
driving conditions, but occasionally the
snowplow may be positioned where it de

ects

air away from the radiator. If this occurs,
stop the vehicle and raise, lower or angle the
snowplow slightly to correct overheating.

NOTE: Only the driver should be in the vehicle
cab when the snowplow is attached.

TRANSPORTING SNOWPLOW

NOTE: For XtremeV™ blades, use care
when driving or entering driveways with the
snowplow in the retracted (vee) position. The
outer ends of the cutting edges could contact
the ground.

WARNING

Position blade so it does not block
headlamp beam.
Do not change blade position while
traveling. You could suddenly lower blade
accidentally.

CAUTION

Transport speed should not exceed
45 mph (72 km/h). Further reduce speed
under adverse travel conditions.

Содержание Minute Mount 2 system

















































































































Результаты поиска

Содержание Minute Mount 2 system

Отзывы:

Похожие инструкции для Minute Mount 2 system

Бренды по названию

Популярные бренды

Fisher Minute Mount 2 system, Руководство пользователя

Результаты поиска

Содержание Minute Mount 2 system

Отзывы:

Похожие инструкции для Minute Mount 2 system

Бренды по названию

Популярные бренды