Fisher Minute Mount 2 system Скачать руководство пользователя страница 100

Страница: 100 / 112

Lit. No. 44224, Rev. 14

101

August 15, 2011

WARNING

To prevent accidental movement of
the blade, always turn the control OFF
whenever the snowplow is not in use. The
power indicator light will turn OFF.

Air Removal – XtremeV™ Blades

11. Turn the control ON and completely extend

and retract the driver-side wing several times.
With all rams fully retracted, turn the control
OFF.

12. Fill the reservoir to the top of the

ll hole and

replace the

ll plug.

NOTE: Loosen

ll plug slowly to relieve any

pressure in the reservoir.

13. Repeat Steps 11 and 12 for the passenger-

side wing.

14.

HT Series™ Blades:

Fill the reservoir to

within 2-1/2" from the top of the

ll hole and

replace the

ll plug.

All other Straight Blades:

Fill the reservoir to

the top of the

ll hole and replace the

ll plug.

MAINTENANCE

Содержание Minute Mount 2 system

















































































































Результаты поиска

Содержание Minute Mount 2 system

Отзывы:

Похожие инструкции для Minute Mount 2 system

Бренды по названию

Популярные бренды

Fisher Minute Mount 2 system, Руководство пользователя

Результаты поиска

Содержание Minute Mount 2 system

Отзывы:

Похожие инструкции для Minute Mount 2 system

Бренды по названию

Популярные бренды