Fisher Minute Mount 2 system Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 112

background image

Lit. No. 44224, Rev. 14

55

August 15, 2011

OPERATING YOUR SNOWPLOW

Function Description of Operation

L

(Angle
Left)

With wings in a straight line, move the
control lever straight to the left to move
both wings to the angle left position to
cast snow to the driver's left side. The left
wing retracts while the right wing extends.
Function times out after 3.0 (XtremeV™)
or 3.25 seconds (XLS™).

R

(Angle
Right)

With wings in a straight line, move the
control lever straight to the right to move
both wings to the angle right position
to cast snow to the driver's right side.
The right wing retracts while the left
wing extends. Function times out after
3.0 (XtremeV) or 3.25 seconds (XLS).

NOTE: If control function times out before
desired blade movement is complete, release
the lever to the center position, then move
back into the desired function.

Scoop/Retract (Vee) Blade Position

Moving the control lever from the center position
toward the word SCOOP or RETRACT (VEE) on
the face of the control body will cause both wings
to move at the same time into the following blade
positions.

Function Description of Operation

SCOOP

Move the control lever toward the word
SCOOP on the control face to extend both
wings forward into the scoop position.
Function times out after 5.0 (XtremeV) or
5.5 seconds (XLS).

RETRACT

(VEE)

Move the control lever toward the word
RETRACT (VEE) on the control face to
draw both wings into the fully retracted
(vee) position. Function times out after
3.0 (XtremeV) or 4.5 seconds (XLS).

«
...
52
53
54
55
56
...
»

Содержание Minute Mount 2 system

















































































































Отзывы:

Нет отзывов

Похожие инструкции для Minute Mount 2 system

Бренд: Oki Страницы: 2

Бренд: A-Tach Mounts Страницы: 2

Бренд: Sunx Страницы: 2

Gemineye EC2014-C

Бренд: Ecco Страницы: 10

Reflex 5500 Series

Бренд: Ecco Страницы: 12

CurrentWatch EAC Series

Бренд: Eaton Страницы: 4

Бренд: Padwico Страницы: 28

Бренд: Panasonic Страницы: 4

Бренд: Daikin Страницы: 52

Krisp Socket Assembly Kit For Straight and Offset...

Бренд: Keating Of Chicago Страницы: 1

Бренд: Anslut Страницы: 12

Бренд: Kia Страницы: 54

Бренд: Metra Electronics Страницы: 2

Бренд: Southern Enterprises Страницы: 4

Бренд: Ohlins Страницы: 8

iBoard IB-ZK406

Бренд: APS Auto Parts Specialist Страницы: 3

Бренд: PCB Piezotronics Страницы: 15

Powerbridge TSV

Бренд: Fishman Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды