Fimer PVS-100-TL B2 Скачать руководство пользователя страница 52

Страница: 52 / 136

3. Cables bending radius.

Sides

(C)

minimum required free space may depends from cable

type (cable dimension, bending radius, etc..). This evaluation

must be done by the installer during the plant design phase (refer

“Routing the cable to the inverter”

paragraph for more

information). In any case the minimum required free space useful

for a proper ventilation of the unit (near side fans) cannot be under

15cm

on the right side and

30cm

on the left side.

NOTE –

In case of manual installation, using handles

(04)

, consider a free side space to lift the inverter of 60 cm

minimum on both sides.

NOTE –

In case of installation with lifting equipments

(eyebolts and ropes) the side distances (C) could be reduced

at the minimum required but a subsequent manual lifting it

will no longer be possible: in this case the lifting equipments

should remain available on the field for any subsequent

operation.

5.2.4 Installation of multiple units

• In case of installation of multiple units in the same place, position

the inverter side by side paying attention to keep the minimum

clearance distances (measured from the outer edge of units) as

shown in the picture below.

30 cm

• The installation of two inverters positioned back to back is also

permitted on a structure which must be composed of a 2 or 3

frame supports (refer to

“Bracket assembly”

paragraph). In this

case the minimum recommended clearance distance between

the units in order to avoid the use of an air deflector is 30cm.

30 cm

5.2.5 Wireless signal environmental checks

The inverter can be commissioned and monitored using the

wireless communication channel. The WLAN board of the inverter

uses radio waves to transmit and receive data. It is therefore

important to assess this factor in order to have an optimal

installation.

Walls made in reinforced concrete and surfaces covered with

metal (doors, shutters, etc.) might significantly reduce the reach of

the device which, even in optimal conditions, is approximately 40

metres in free space.

Before installing the inverter it is therefore recommended to

check the strength of wireless signal by means a mobile device

(smartphone, tablet or notebook) by connecting it to the wireless

router from a position which is close to the intended installation

position of the inverter.

The radio signal level between the inverter and the wireless router

can be improved in a two ways:

1. Find a new position for the router considering the different types

of materials which the radio signal will have to pass through

Material

Relative signal reduction

Open field

0% (strength of approximately 40

metres)

Wood / Glass

From 0 to 10%

Stone / Plywood

From 10 to 40%

Reinforced concrete

From 60 to 90%

Metal

Up to 100 %

NOTE –

The quality of the RF signal can be assessed during

the installation stage where the signal is displayed in dBm.

2. Install a wireless signal repeater and place it in an area between

the inverter and the router, trying in this way to skip the most critical

obstacles.

5.2.6 Installations above 2000 metres

Due to the rarefaction of the air (at high altitudes), particular

conditions may occur and it should be considered when choosing

the place of installation:

Less efficient cooling and therefore a greater likelihood of a

device power reduction (derating) occur due to high internal

temperatures.

Reduction in the dielectric resistance of the air which, in the

presence of high operating voltages (DC input), can create

electric arcs (electrical discharges) that may damage the device.

When the altitude increases, the failure rate of some electronic

components increases exponentially due to cosmic radiation.

NOTE –

All installations at altitudes exceeding 2000

metres are not recommended on the basis of the criticalities

indicated above.

5.2.7 Installations with a high level of humidity

ATTENTION –

Never open the inverter in the case of rain,

snow or a level of humidity >95%.

ATTENTION –

Always carefully seal all unused openings.

Even though the device is equipped with an anti-condensation

valve, air with extremely high levels of humidity can lead to the

creation of condensation inside the inverter.

As the inverter is almost completely insulated from the outside,

condensation can also form after installation in certain weather

conditions.

Содержание PVS-100-TL B2









































































































































Результаты поиска

Содержание PVS-100-TL B2

Отзывы:

Похожие инструкции для PVS-100-TL B2

Бренды по названию

Популярные бренды

Fimer PVS-100-TL B2, Руководство по эксплуатации продукта

Результаты поиска

Содержание PVS-100-TL B2

Отзывы:

Похожие инструкции для PVS-100-TL B2

Бренды по названию

Популярные бренды