manualshive.com logo in svg

FG Wilson PowerWizard 1.1, Техническое руководство

Поделиться
Скачать
FG Wilson PowerWizard 1.1 Скачать руководство пользователя страница 29

29

3. SCaDa DaTalInK

When an output is configured for the SCADA data link, its active state can be sent over the Modbus.

5.3  analogue Input Programming

PowerWizard 2.1 and 1.1+ have three analogue input channels and PowerWizard 1.1 has two. For a Mechanical Unit Injector 
Engine (MUI), two of the inputs are dedicated to monitor the engine coolant temperature and the engine oil pressure.  The 
Analogue Input #3 has a default configuration to "disabled". 
All three analogue inputs can be programmed to monitor any supported parameter in Table 8 for an Electronic Unit Injector 
Engine (EUI). In this case the engine oil pressure sensor and the engine coolant temperature sensor are wired to the Engine ECM 
and not to the PowerWizard. 

Temperatures

Engine Coolant Temperature

Engine Oil Temperature

Pressures

Engine Oil Pressure

levels

Engine Fuel Level

External Tank Fuel Level

other

Customer Parameter #1
Customer Parameter #2
Customer Parameter #3

SCADA Data Link (PowerWizard 2.1 Only)

Desired Engine Speed Command

Urea Level

Table 8: list of supported parameters

Analogue inputs can be configured from menu options:
MAIN MENU > CONFIGURE > INPUTS & OUTPUTS > ANALOGUE INPUTS
There are three USAGE TYPES for an available input: DISABLED, RESISTIVE and VOLTAGE SENDER. Each of the inputs can be 
configured to have HIGH WARNING, LOW WARNING, HIGH SHUTDOWN or LOW SHUTDOWN with thresholds. Each event 
associated with the input also has a programmable time delay.

1. resistive sender

DATA IDENTIFICATION for a resistive sender can be selected from the list in Table 8, e.g. temperature, pressure or level. The MAP 
SELECTION NUMBER is used to select a map in connection with the sender. PowerWizard has up to 25 maps available for resistive 
senders as shown in Table 9. Each map is defined in factory and contains up to 25 interpolation points.

Map

Description

Map 1

VDO Pressure Curve 4

Map 2

Pressure 246-8150

Map 3

VDO Temperature Curve 1

Map 4

Temp 191-6587

Map 5

VDO Temperature Curve 2

Map 6

Temp 349-2458

Map 7

Fozmula Level 1

Map 8

Linear 0 to 2000 ohm

Map 9

XQ Fuel 1

Map 10

XQ Fuel 2

Map 11-25

Future Use

Table 9

Содержание PowerWizard 1.1


















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды