Festo DGC G Series Скачать руководство пользователя страница 111 | Manualshive

Страница: 111 / 136

background image

19 / 44

Festo 7DGC-KFa_en

Assembling the linear drive

4.1.2

When assembling a linear drive wearing parts, such as the sealing band, seals, buffers, covers, clips and the complete
piston, can be replaced.
The wearing parts are ordered from the online spare parts catalogue (spareparts.Festo.com) quoting the appropriate part
number (dependent on the size of the linear drive).
The part number is an x-stroke part number. In addition to the part number, you must also specify the stroke of your
linear drive when ordering. The stroke can be determined from the type code on the name plate of the linear drive
(see order example below). Using this information you can calculate the necessary sealing band length.

Cutting the new sealing band to length

The exact length of the sealing band is determined by the 0-stroke of the respective type and the stroke of the linear

drive. The stroke is specified by the type code on the name plate. Check the length of the new sealing band and shorten

it to length (0-hub + hub) as necessary. See order example.

Type

Length L

0

DGC-8-…-KF

140 mm

DGC-12-…-KF

160 mm



Example: DGC-12-405-KF
0-stroke:

160 mm

Stroke:

405 mm

Length of the sealing band = 0- stroke = 565 mm

The length of the sealing band calculated in this way is a theoretical value. Component tolerances may make it necessary
to adjust the length of the sealing band after installation.

Note

Sturdy general purpose scissors or metal shears are best for cutting the sealing band.

Warning

Do not bend the sealing band as this may cause damage or tearing and reduce its service life.

Greasing whilst assembling

When assembling the linear drives, various components have to be greased in accordance with the table below.

Component

Lubricant

Greasing instructions

Cylinder barrel

Festo LUB-KC1

1)

Apply a layer of grease to the slot and all around and along the entire length of
the cylinder bore.

Sealing band

Festo LUB-KC1

1)

Apply a layer of grease all around and along the entire length.

Piston

Festo LUB-KC1

1)

Grease all around.

Seal, piston

Festo LUB-KC1

1)

Grease all around.

1)

See “Assembly aids” in the online spare parts catalogue on the Festo website (www.Festo.com).

Grease the sealing band, the piston and the inside of the cylinder barrel.

•

Observe the greasing instructions in the table at the start of this chapter.
Thread the sealing band into the through-hole in the piston.

•

«
...
109
110
111
112
113
...
»

Содержание DGC G Series









































































































































Отзывы:

Нет отзывов

Похожие инструкции для DGC G Series

C1400-CO-VS-0S-I03

Бренд: NTI AG Страницы: 20

PARAMAX M Series

Бренд: Sumitomo Drive Technologies Страницы: 24

Бренд: Penta KB Power Страницы: 20

Бренд: Mitsubishi Electric Страницы: 59

Бренд: Mitsubishi Electric Страницы: 66

Бренд: Mitsubishi Electric Страницы: 73

Бренд: Mitsubishi Electric Страницы: 303

Бренд: Mitsubishi Electric Страницы: 22

Бренд: Mitsubishi Electric Страницы: 826

Бренд: KB Electronics Страницы: 18

IM.60 24V + CPS

Бренд: Fancom Страницы: 55

Бренд: AC Tech Страницы: 2

Бренд: Pepperl+Fuchs Страницы: 2

Бренд: Parallax Страницы: 8

VLT AutomationDrive FC 303

Бренд: Danfoss Страницы: 105

Universal IO Drive

Бренд: Raymarine Страницы: 17

ALLEN-BRADLEY 1391-DES

Бренд: AB Quality Страницы: 149

Бренд: M-system Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды