Festo DGC G Series Скачать руководство пользователя страница 42

Страница: 42 / 136

42 / 48

Festo 07DGC-Ga_en

Replacing the buffer strips

4.3.4

Remove the cushioning components from the end caps.

•

Note

The cushioning components can be replaced even when the end caps are
attached.

Grease the backs of the new cushioning components and insert them into

•

the end caps.

Replacing the sealing rings for the supply ports in the end caps

4.3.5

Unscrew and remove the plug screws for the supply ports from the end cap

•

and remove the sealing rings.

Note

The sealing rings can be replaced even when the end cap is inserted.

Insert the new sealing rings in the supply ports by repeating the steps in

•

reverse order and tighten the plug screws using the appropriate torque
(see table).

Type

Torque

DGC-50-…-G

16 Nm

DGC-63-…-G

18 Nm

Содержание DGC G Series









































































































































Результаты поиска

Содержание DGC G Series

Отзывы:

Похожие инструкции для DGC G Series

Бренды по названию

Популярные бренды

Festo DGC G Series, Инструкции по ремонту

Результаты поиска

Содержание DGC G Series

Отзывы:

Похожие инструкции для DGC G Series

Бренды по названию

Популярные бренды